- 您现在的位置：买卖IC网 > PDF目录11202 > ATSAM3A4CA-AU (Atmel)IC MCU 2X128KB CORTEX-M3 100-QFP PDF资料下载
参数资料
| 型号： | ATSAM3A4CA-AU |
| 厂商： | Atmel |
| 文件页数： | 16/71页 |
| 文件大小： | 0K |
| 描述： | IC MCU 2X128KB CORTEX-M3 100-QFP |
| 标准包装： | 90 |
| 系列： | SAM3A |
| 核心处理器： | ARM? Cortex?-M3 |
| 芯体尺寸： | 32-位 |
| 速度： | 84MHz |
| 连通性： | CAN，I²C，IrDA，LIN，MMC，SPI，SSC，UART/USART，USB |
| 外围设备： | 欠压检测/复位，DMA，I²S，POR，PWM，WDT |
| 输入/输出数： | 63 |
| 程序存储器容量： | 256KB（256K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 64K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.62 V ~ 1.95 V |
| 数据转换器： | A/D 16x12b，D/A 2x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-LQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页
25
11057BS–ATARM–13-Jul-12
SAM3X/A
25
11057BS–ATARM–13-Jul-12
SAM3X/A
The Supply Controller, zero-power power-on reset, RTT, RTC, Backup registers and 32 kHz
Oscillator (RC or crystal oscillator selected by software in the Supply Controller) are running.
The regulator and the core supply are off.
Backup Mode is based on the Cortex-M3 deep-sleep mode with the voltage regulator disabled.
The SAM3X/A series can be awakened from this mode through the Force Wake-up pin (FWUP),
and Wake-up input pins WKUP0 to WKUP15, Supply Monitor, RTT or RTC wake-up event. Cur-
rent Consumption is 2.5 A typical on VDDBU.
Backup mode is entered by using WFE instructions with the SLEEPDEEP bit in the System Con-
trol Register of the Cortex-M3 set to 1. (See the Power management description in the “ARM
Cortex M3 Processor” section of the product datasheet).
Exit from Backup mode happens if one of the following enable wake up events occurs:
FWUP pin (low level, configurable debouncing)
WKUPEN0-15 pins (level transition, configurable debouncing)
SM alarm
RTC alarm
RTT alarm
5.5.2
Wait Mode
The purpose of the wait mode is to achieve very low power consumption while maintaining the
whole device in a powered state for a startup time of less than 10 s.
In this mode, the clocks of the core, peripherals and memories are stopped. However, the core,
peripherals and memories power supplies are still powered. From this mode, a fast start up is
available.
This mode is entered via Wait for Event (WFE) instructions with LPM = 1 (Low Power Mode bit in
PMC_FSMR). The Cortex-M3 is able to handle external events or internal events in order to
wake-up the core (WFE). This is done by configuring the external lines WKUP0-15 as fast
startup wake-up pins (refer to Section 5.7 “Fast Start-Up”). RTC or RTT Alarm and USB wake-up
events can be used to wake up the CPU (exit from WFE).
Current Consumption in Wait mode is typically 23 A for total current consumption if the internal
voltage regulator is used or 15 A if an external regulator is used.
Entering Wait Mode:
Select the 4/8/12 MHz Fast RC Oscillator as Main Clock
Set the LPM bit in the PMC Fast Startup Mode Register (PMC_FSMR)
Execute the Wait-For-Event (WFE) instruction of the processor
Note:
Internal Main clock resynchronization cycles are necessary between the writing of MOSCRCEN
bit and the effective entry in Wait mode. Depending on the user application, Waiting for
MOSCRCEN bit to be cleared is recommended to ensure that the core will not execute undesired
instructions.
5.5.3
Sleep Mode
The purpose of sleep mode is to optimize power consumption of the device versus response
time. In this mode, only the core clock is stopped. The peripheral clocks can be enabled. This
mode is entered via Wait for Interrupt (WFI) or Wait for Event (WFE) instructions with LPM = 0 in
PMC_FSMR.
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC7128BCPZ126-RL | IC DAS MCU ARM7 ADC/DDS 64-LFCSP |
| ADUC848BCPZ8-3 | IC MCU FLASH W/16BIT ADC 56-CSP |
| ADUC848BCPZ8-5 | IC MCU FLASH W/16BIT ADC 56-CSP |
| ADUC848BSZ8-3 | IC MCU FLASH W/16BIT ADC 52MQFP |
| ADUC7020BCPZ62I-RL | IC MCU 12BIT 1MSPS I2C 40-LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATSAM3A4CA-CU | 功能描述:ARM微控制器 - MCU BGA100,GREEN, IND TEMP, MRL A RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| ATSAM3A8CA-AU | 功能描述:ARM微控制器 - MCU QFP100,GREEN, IND TEMP, MRLA RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| ATSAM3A8CA-CU | 功能描述:ARM微控制器 - MCU BGA100,GREEN, IND TEMP, MRLA RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| ATSAM3N00AA-AU | 功能描述:ARM微控制器 - MCU LQFP, Green, IND TEMP, MRL a RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| ATSAM3N00AA-AUR | 制造商:Atmel Corporation 功能描述:LQFP,GREEN,IND TEMP,MRL A,T&R - Tape and Reel 制造商:Atmel Corporation 功能描述:IC MCU 32BIT 16KB FLASH 48LQFP |
发布紧急采购，3分钟左右您将得到回复。