参数资料
| 型号： | ATSTK501 |
| 厂商： | Atmel |
| 文件页数： | 9/29页 |
| 文件大小： | 0K |
| 描述： | ADAPTER KIT FOR 64PIN AVR MCU |
| 标准包装： | 1 |
| 附件类型： | STK500 扩展模块 |
| 适用于相关产品： | 64 引脚 megaAVR 设备 |
| 配用： | ATADAPCAN01-ND - EXTENSION CAN ADD-ON TO STK500/1 ATSTK500-ND - PROGRAMMER AVR STARTER KIT |
| 相关产品： | ATMEGA128L-8AN-ND - MCU AVR 128KB FLASH 8MHZ 64-TQFP ATMEGA128L-8MN-ND - MCU AVR 128KB FLASH 8MHZ 64QFN ATMEGA128L-8AURTR-ND - MCU AVR 128KB FLASH 8MHZ 64-TQFP ATMEGA128-16MUR-ND - MCU AVR 128KB FLASH 16MHZ 64QFN ATMEGA128-16AUR-ND - MCU AVR 128KB FLASH 16MHZ 64TQFP ATMEGA128-16MN-ND - MCU AVR 128KB FLASH 16MHZ 64QFN ATMEGA128-16ANRTR-ND - MCU AVR 128KB FLASH 16MHZ 64TQFP ATMEGA128-16MNRTR-ND - MCU AVR 128KB FLASH 16MHZ 64QFN ATMEGA128-16AN-ND - MCU AVR 128KB FLASH 16MHZ 64TQFP ATMEGA128L-8MNRTR-ND - MCU AVR 128KB FLASH 8MHZ 64QFN 更多... |
| 其它名称： | Q1167170 STK501 STK501-ND |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Using the STK501 Top Module
2.2.2
2.2.2.1
2.2.2.2
2.2.2.3
2.2.2.4
PORT G/AUX
PG0 - PG4
A16
SRAMEN
PEN
In addition to the normal Port G pins, this connector has some extra signals. See Figure
Figure 2-4. PORTG/AUX
1 2
PG0
PG1
PG2
PG3
PG4
A16
SRAMEN
PEN
GND
VTG
PORT G/AUX
These are general I/O ports for the ATmega128(L) and connect to the ZIF socket and
the TQFP footprint. The PG3 and PG4 signals are routed through the TOSC switch
since these pins also are inputs for a 32 kHz oscillator. For a description on the TOSC
Note:
ATmega103(L) does not have Port G.
This line goes to A16 (most significant address bit) on the SRAM. See Section 2.5 for
more information about this signal. can be connected to any AVR pin.
The SRAMEN signal controls if the SRAM is enabled or not. To enable the SRAM a
LOW level should be applied to this pin. See “ External SRAM ” , Section 2.5, for more
information on how to use this signal. This signal is pulled high by default.
The PEN pin is connected to the PEN pin on the ATmega103(L)/128(L). This pin is
described in the programming section of the ATmega103(L) and ATmega128(L)
datasheets.
2.3
Programming the The ATmega103(L) and ATmega128(L) can be programmed using both SPI and High-
ATmega103(L)/
128(L)
voltage Parallel Programming. This sub section will explain how to connect the program-
ming cables to successfully use one of these two modes. The AVR Studio STK500
software is used in the same way as for other AVR parts.
Note:
The ATmega128(L) also supports Self Programming. See AVR109 application
note for more information on this topic.
2.3.1
In-System
Programming
To program the ATmega103(L) or ATmega128(L) using ISP programming mode, con-
nect the 6-wire cable between the ISP6PIN connector on the STK500 board and the ISP
The device can be programmed using the serial programming mode in the AVR Studio
STK500 software.
Note:
See the STK500 User Guide for information on how to use the STK500 front-
end software for ISP programming.
AVR ? STK501 User Guide
2-3
相关PDF资料 |
PDF描述 |
|---|---|
| ATSTK502 | MOD EXPANSION AVR STARTER 500 |
| ATSTK503 | STARTER KIT AVR EXP MODULE 100P |
| ATSTK504 | STARTER KIT AVR EXP MOD 100P LCD |
| ATSTK505 | ADAPTER KIT FOR 14PIN AVR MCU |
| ATSTK520 | ADAPTER KIT FOR 90PWM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATSTK502 | 功能描述:插座和适配器 Expansion module for STK500 Starter Kit RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| ATSTK503 | 功能描述:插座和适配器 Expansion module for STK500 Starter Kit RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| ATSTK504 | 功能描述:插座和适配器 Expansion module for STK500 Starter Kit RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| ATSTK505 | 功能描述:插座和适配器 Expansion module for STK500 Dev Board RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| ATSTK520 | 功能描述:开发板和工具包 - AVR AVR Starter Kit Ext 8K FLASH 3PSC RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
发布紧急采购，3分钟左右您将得到回复。