参数资料
| 型号： | ATSTK503 |
| 厂商： | Atmel |
| 文件页数： | 15/17页 |
| 文件大小： | 0K |
| 描述： | STARTER KIT AVR EXP MODULE 100P |
| 标准包装： | 1 |
| 附件类型： | STK500 扩展模块 |
| 适用于相关产品： | 100 引脚 megaAVR 设备 |
| 配用： | ATSTK500-ND - PROGRAMMER AVR STARTER KIT |
| 相关产品： | ATMEGA1280-16AUR-ND - MCU AVR 128K FLASH 16MHZ 100TQFP ATMEGA1280V-8AURTR-ND - MCU AVR 128K FLASH 8MHZ 100TQFP ATMEGA1280-16CUR-ND - MCU AVR 128K FLASH 16MHZ 100CBGA ATMEGA1280V-8CURTR-ND - MCU AVR 128K FLASH 8MHZ 100CBGA ATMEGA640V-8CU-ND - IC MCU AVR 64K FLASH 100-CBGA ATMEGA640V-8AU-ND - IC MCU AVR 64K FLASH 100-TQFP ATMEGA640-16CU-ND - IC MCU AVR 64K FLASH 100-CBGA ATMEGA640-16AU-ND - IC MCU AVR 64K FLASH 100-TQFP ATMEGA2560V-8CU-ND - IC MCU AVR 256K FLASH 100-CBGA ATMEGA2560-16CU-ND - IC MCU AVR 256K FLASH 100-CBGA 更多... |
Troubleshooting Guide
Programming problems
Problem
ISP programming
does not work
Cause Solution
ISP cable is not connected Connect a 6-pin cable between the ISP6PIN
connector on STK500 and the ISP connector on
STK503. See also Programming the AVR.
ISP programming
The ISP clock is to fast if
Make sure the clock switch on STK503 is in the
does not work
the AVR is running at a low right position. In the Board page of the
clock frequency.
programming dialog in AVR Studio, try reducing
the ISP clock frequency.
High-Voltage
The 10-pin cables are not
See the Programming the AVR chapter for
programming does connected correctly.
not work.
setup.
High-Voltage
The BSEL2, OSCSEL,
See the Programming the AVR chapter for
programming does RESET and VTARGET
setup.
not work.
High-Voltage
jumpers on STK500 are not
set right.
The STK504 clock switch is Set the switch to the STK500 position. See also
programming does in the wrong position.
not work.
General problems
Problem Cause
Some of the port pins are The AVR is not
Programming the AVR.
Solution
Make sure the chip is properly aligned in the
not working .
The code isn't running.
properly mounted in
the ZIF socket.
The AVR has
no/wrong clock
source.
socket. When the spring-loaded latch is
depressed, the chip should fit nicely into the
bottom of the socket.
According to the clock fuse setting, select the
appropriate clock source on STK500 and
STK503. Check the OSCSEL jumper on
STK500 and clock switch on STK503. If you are
using a crystal in one of the sockets, check that
it is firmly mounted in its socket.
The AVR will not run on x The clock frequency Check that you are running the AVR within
MHz, but works ok on
is exceeding the
specifications. Check the speed grade of the
lower frequencies.
clock rate of the AVR AVR and consult the datasheet for operating
(at a certain
operating voltage).
The AVR will not run on x Crystals should be
frequencies and voltages.
Place the crystal in the socket on STK503. Set
MHz, but works ok on
placed in the crystal the clock switch to the position closest to the
lower frequencies. I have socket on STK503.
crystal socket..
a x MHz crystal mounted
on STK500
15
相关PDF资料 |
PDF描述 |
|---|---|
| ATSTK504 | STARTER KIT AVR EXP MOD 100P LCD |
| ATSTK505 | ADAPTER KIT FOR 14PIN AVR MCU |
| ATSTK520 | ADAPTER KIT FOR 90PWM |
| ATSTK521 | EXPANSION MODULE ATSTK500 |
| ATSTK524 | KIT STARTER ATMEGA32M1/MEGA32C1 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATSTK504 | 功能描述:插座和适配器 Expansion module for STK500 Starter Kit RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| ATSTK505 | 功能描述:插座和适配器 Expansion module for STK500 Dev Board RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x |
| ATSTK520 | 功能描述:开发板和工具包 - AVR AVR Starter Kit Ext 8K FLASH 3PSC RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| ATSTK521 | 功能描述:子卡和OEM板 ATSTK500 expansion module for AT90PWM81 RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| ATSTK524 | 功能描述:开发板和工具包 - AVR Starter Kit for ATMEGA32M1/C1 RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
发布紧急采购，3分钟左右您将得到回复。