参数资料
| 型号： | ATTINY13A-MMU |
| 厂商： | Atmel |
| 文件页数： | 52/67页 |
| 文件大小： | 0K |
| 描述： | IC MCU AVR 1K FLASH 20MHZ 10-DFN |
| 产品培训模块： | MCU Product Line Introduction tinyAVR Introduction |
| 标准包装： | 490 |
| 系列： | AVR® ATtiny |
| 核心处理器： | AVR |
| 芯体尺寸： | 8-位 |
| 速度： | 20MHz |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 6 |
| 程序存储器容量： | 1KB（512 x 16） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 64 x 8 |
| RAM 容量： | 64 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.8 V ~ 5.5 V |
| 数据转换器： | A/D 4x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 包装： | 托盘 |
| 产品目录页面： | 612 (CN2011-ZH PDF) |
| 配用： | ATSTK600-DIP40-ND - STK600 SOCKET/ADAPTER 40-PDIP ATAVRDRAGON-ND - KIT DRAGON FLASH MEM AVR ATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM ATJTAGICE2-ND - AVR ON-CHIP D-BUG SYSTEM |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页当前第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
32
8126F–AVR–05/12
ATtiny13A
Modules can be shut down in Idle and Active modes, significantly helping to reduce the overall
power consumption. In all other sleep modes, the clock is already stopped. See “Supply Current
of I/O Modules” on page 124 for examples.
7.4
Minimizing Power Consumption
There are several issues to consider when trying to minimize the power consumption in an AVR
controlled system. In general, sleep modes should be used as much as possible, and the sleep
mode should be selected so that as few as possible of the device’s functions are operating. All
functions not needed should be disabled. In particular, the following modules may need special
consideration when trying to achieve the lowest possible power consumption.
7.4.1
Analog to Digital Converter
If enabled, the ADC will be enabled in all sleep modes. To save power, the ADC should be dis-
abled before entering any sleep mode. When the ADC is turned off and on again, the next
conversion will be an extended conversion. Refer to “Analog to Digital Converter” on page 82 for
details on ADC operation.
7.4.2
Analog Comparator
When entering Idle mode, the Analog Comparator should be disabled if not used. When entering
ADC Noise Reduction mode, the Analog Comparator should be disabled. In the other sleep
modes, the Analog Comparator is automatically disabled. However, if the Analog Comparator is
set up to use the Internal Voltage Reference as input, the Analog Comparator should be dis-
abled in all sleep modes. Otherwise, the Internal Voltage Reference will be enabled,
independent of sleep mode. Refer to “Analog Comparator” on page 79 for details on how to con-
figure the Analog Comparator.
7.4.3
Brown-out Detector
If the Brown-out Detector is not needed in the application, this module should be turned off. If the
Brown-out Detector is enabled by the BODLEVEL fuses, it will be enabled in all sleep modes,
and hence, always consume power. In the deeper sleep modes, this will contribute significantly
to the total current consumption. See “Brown-out Detection” on page 37 and “Software BOD Dis-
able” on page 31 for details on how to configure the Brown-out Detector.
7.4.4
Internal Voltage Reference
The Internal Voltage Reference will be enabled when needed by the Brown-out Detection, the
Analog Comparator or the ADC. If these modules are disabled as described in the sections
above, the internal voltage reference will be disabled and it will not be consuming power. When
turned on again, the user must allow the reference to start up before the output is used. If the
reference is kept on in sleep mode, the output can be used immediately. Refer to “Internal Volt-
age Reference” on page 38 for details on the start-up time.
7.4.5
Watchdog Timer
If the Watchdog Timer is not needed in the application, this module should be turned off. If the
Watchdog Timer is enabled, it will be enabled in all sleep modes, and hence, always consume
power. In the deeper sleep modes, this will contribute significantly to the total current consump-
tion. Refer to “Interrupts” on page 45 for details on how to configure the Watchdog Timer.
相关PDF资料 |
PDF描述 |
|---|---|
| HSHM-GUIDE-PIN-1 | CONN HSHM GUIDE PIN M4-.7-6G |
| ATTINY13A-SU | IC MCU AVR 1K FLASH 20MHZ 8SOIC |
| ATTINY13A-PU | IC MCU AVR 1K FLASH 20MHZ 8PDIP |
| ATTINY48-MUR | MCU AVR 4KB FLASH 12MHZ 32QFN |
| ATTINY13A-MU | IC MCU AVR 1K FLASH 20MHZ 20-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATTINY13A-MMU SL371 | 制造商:Atmel Corporation 功能描述:MCU 8BIT ATTINY RISC 1KB FLASH 2.5V/3.3V/5V 10PIN MLF - Trays |
| ATTINY13A-MMU SL383 | 制造商:Atmel Corporation 功能描述:AVR, 1KB FLASH, 64B EE, 64B SRAM - WQFN/MLF, IND TEMP, GREEN - Tape and Reel |
| ATTINY13A-MMUR | 功能描述:8位微控制器 -MCU AVR 1KB FLSH 64B EE 64B SRAM-20MHz, IND RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ATTINY13A-MU | 功能描述:8位微控制器 -MCU 1KB In-system Flash 20MHz 1.8V-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ATTINY13A-MUR | 功能描述:8位微控制器 -MCU AVR 1KB FLSH 64B EE 64B SRAM-20MHz, IND RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。