参数资料
| 型号： | AXC81F40410 |
| 厂商： | Panasonic Electric Works |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | CONN PLUG COVER 40POS |
| 标准包装： | 1,000 |
| 系列： | CF |
| 附件类型： | 帽盖（盖），外壳 |
| 位置数： | 40 |
| 适用于相关产品： | CF 系列插头 |
| 配用： | AXC61F4040-ND - CONN PLUG 40POS 0.40MM GOLD |
Notes on Using Micro Coaxial Connectors
Notes on Using Micro Coaxial Connectors
NOTES (Unit: mm)
Safety precautions
Observe the following safety precautions to prevent accidents
and injuries.
1) The use of the connector outside of the speci?ed rated current
and breakdown voltage ranges may cause abnormal heating,
smoke, and ?re.
Never use the connector beyond the speci?ed ranges of the
product.
2) In order to avoid accidents, make sure you have thoroughly
reviewed the speci?cations before use.
Consult us if you plan to use the product in a way not covered by
the speci?cations.
3) We are consistently striving to improve quality and reliability.
However, the fact remains that electrical components and
devices generally fail at a given statistical probability.
Furthermore, their durability varies depending on where and
how they are used. Please be sure to verify electrical
components and devices under actual conditions before use.
Continuously using them in a state of degraded performance
may cause deterioration in insulation performance, thus
resulting in abnormal heat generation, smoke generation, or ?re.
To avoid that, we ask you to implement safe designs that include
? Soldering
1) Manual soldering.
? Since this connector is the low pro?le type the amount of solder
supplied should be closely monitored.
Too much solder during manual soldering may cause solder
creeping near the contacting part or a short circuit with the shell
(GND).
? Make sure that the soldering iron tip is heated within the
temperature and time limits indicated in the speci?cations.
? Flux from the solder wire may adhere to the contact surfaces
during soldering operations. After soldering, carefully check the
contact surfaces and clean off any ?ux before use.
? Be aware that a load applied to the connector terminals while
soldering may displace the contact.
? Thoroughly clean the iron tip.
CS series
? Receptacle
Recommended PC board pattern (mounting pad layout)
(Top view)
A ± 0.05
B ± 0.05
redundancy, ?re prevention, and malfunction prevention. Also,
please conduct periodic maintenance so that no accidents
resulting in injury or death, ?re, or harm to society will be caused
as a result of product failure or service life.
About plug
The plug of this product is wired by soldering the 0.25 mm pitch
(CS)/0.4 mm pitch (CF) cable.
0.25 ± 0.03
0.50 ± 0.03
0.25 ± 0.03
C ± 0.05
D ± 0.05
If you will be harnessing, carry it out based on the separately
attached “Plug Assembly Procedures”. Make sure to get familiar
E ± 0.05
F ± 0.05
G ± 0.05
Insulation
with and observe all the precautions in the procedures.
Note: If you would like “Plug Assembly Procedures”, please
inquire at one of our sales of?ces.
? Caution regarding harness handling procedures.
To prevent the cable from being severed and to prevent damage
to the product, please handle carefully making sure not to apply
undue stress to the base of the cable after connecting it and
after mating the connector.
? Caution regarding harness design
To prevent the cable from being severed and to prevent damage
to the product, please place and secure the cable in a way that
prevents the base of the cable from becoming stressed.
About receptacle
? PC board design
Design the recommended foot pattern in order to secure the
mechanical strength in the soldered areas of the terminal.
? About (CF)
Use all the soldering terminals as GND for connecting GND
stably.
? Connector mounting
When mounting, if there is too much suction nozzle pressure,
the molded and metal parts might deform and break.
Please check beforehand.
Recommended window size of metal mask
Metal mask thickness: When 120 μ m
(Signal terminal portion opening area ratio: 60%)
(GND terminal portion opening area ratio: 70%)
(Shell edge terminal portion at four corners opening area ratio: 60%)
H ± 0.03
B ± 0.03
C ± 0.03
0.50 ± 0.01
0.22 ± 0.01
D ± 0.03
I ± 0.03
G ± 0.03
Dimension table (mm)
Number of
pins/ A B C D E F G H I
dimension
21 7.05 5.75 5.00 4.50 7.40 8.90 9.98 6.85 9.16
41 12.05 10.75 10.00 9.50 12.40 13.90 14.98 11.85 14.16
51 14.55 13.25 12.50 12.00 14.90 16.40 17.48 14.35 16.66
ACCTB12E 201303-T
Panasonic Corporation
Automation Controls Business Division
industrial.panasonic.com/ac/e/
相关PDF资料 |
PDF描述 |
|---|---|
| 3-87631-7 | CONN RCPT 42POS DL .100 CRIMP |
| QMSS-078-06.75-H-D-PC4 | CONN HEADER .635MM 156POS DL SMD |
| 767143182GP | RES ARRAY 1.8K OHM 7 RES 14-SOIC |
| 3505-8126 | CONN RETAINER CLIP 26POS LONG |
| 87131-3 | 20 LOCKING CLIP HSG DR .100CL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AXC81S41710 | 功能描述:CONN MICRO COAX PLUG COVER 41POS RoHS:是 类别:连接器，互连式 >> 矩形 - 配件 系列:CS 标准包装:1,000 系列:* 其它名称:035129-0200351290-0200351290200 |
| AXC81S41714 | 功能描述:CONN MICRO COAX PLUG COVER 41POS RoHS:是 类别:连接器，互连式 >> 矩形 - 配件 系列:CS 标准包装:1,000 系列:* 其它名称:035129-0200351290-0200351290200 |
| AXC81S51710 | 功能描述:CONN MICRO COAX PLUG COVER 51POS RoHS:是 类别:连接器，互连式 >> 矩形 - 配件 系列:CS 标准包装:1,000 系列:* 其它名称:035129-0200351290-0200351290200 |
| AXCONT | 制造商:BOLLE SAFETY 功能描述:AXIS CONTRAST UV ANTI SCR |
| AXCS-2811-256D | 制造商:AXIOHM 功能描述:Axiom - Memory - 256 MB - DIMM 184-pin - DDR - 266 MHz / PC2100 - unbuffered - E |
发布紧急采购，3分钟左右您将得到回复。