参数资料
| 型号： | AXN520045G |
| 厂商： | Panasonic Electric Works |
| 文件页数： | 6/7页 |
| 文件大小： | 0K |
| 描述： | CONN SOCKET .5MM 20POS SMD |
| 其它有关文件： | Connectors SMD-Technical Info |
| 产品变化通告： | P5 Connectors Discontinuation Mar/2012 |
| 标准包装： | 1,000 |
| 系列： | P5 |
| 连接器类型： | 插口，中央触点带 |
| 位置数： | 20 |
| 间距： | 0.020"（0.50mm） |
| 行数： | 2 |
| 安装类型： | 表面贴装 |
| 触点表面涂层： | 金 |
| 包装： | 带卷 (TR) |
| 配接层叠高度： | 5mm |
| 板上方高度： | 0.120"（3.05mm） |
| 配套产品： | AXN620585G-ND - CONN HEADER .5MM 20POS SMD |
NOTES FOR USING SMD TYPE CONNECTORS (Common)
Regarding soldering
1. Re?ow soldering
1) Measure the recommended pro?le
temperature for re?ow soldering by
placing a sensor on the PC board near
the connector surface or terminals. (The
setting for the sensor will differ depending
on the sensor used, so be sure to
carefully read the instructions that comes
with it.)
2) As for cream solder printing, screen
printing is recommended.
3) See the speci?cations and drawings
for the product in question for the metal
mask pattern diagrams.
4) When mounting on both sides of the
PC board and the connector is mounting
on the underside, use adhesives or other
means to ensure the connector is
properly ?xed to the PC board. (Double
re?ow soldering on the same side is
possible.)
5) N 2 re?ow, conducting re?ow soldering
in a nitrogen atmosphere, increases the
For products other than the ones above,
please refer to the latest product
speci?cations.
6) The temperatures are measured at the
surface of the PC board near the
connector terminals. (The setting for the
sensor will differ depending on the sensor
used, so be sure to carefully read the
instructions that comes with it.)
7) The temperature pro?les given in this
catalog are values measured when using
the connector on a resin-based PC
board. When performed re?ow soldering
on a metal board (iron, aluminum, etc.) or
a metal table to mount on a FPC, make
sure there is no deformation or
discoloration of the connector beforehand
and then begin mounting.
2. Hand soldering
1) Set the soldering iron so that the tip
temperature is less than that given in the
table below.
Table A
4) Be aware that soldering while applying
a load on the connector terminals may
cause improper operation of the
connector.
5) Thoroughly clean the soldering iron.
6) Flux from the solder wire may get on
the contact surfaces during soldering
operations. After soldering, carefully
check the contact surfaces and clean off
any solder before use.
7) For soldering of prototype devices
during product development, you can
perform soldering at the necessary
locations by heating with a hot-air gun by
applying cream solder to the foot pattern
beforehand. However, at this time, make
sure that the air pressure does not move
connectors by carefully holding them
down with tweezers or other similar tool.
Also, be careful not to go too close to the
connectors and melt any of the molded
components.
3. Solder reworking
solder ?ow too greatly, enabling wicking
to occur. Make sure that the solder feed
rate and temperature pro?le are
Product name
SMD type connectors
Soldering iron temperature
300 ° C within 5 sec.
350 ° C within 3 sec.
1) Finish reworking in one operation.
2) For reworking of the solder bridge, use
a soldering iron with a ?at tip. To prevent
appropriate.
Soldering conditions
Please use the re?ow temperature pro?le
conditions recommended below for
re?ow soldering. Please contact us
before using a temperature pro?le other
than that described below (e.g. lead-free
solder).
? Narrow-pitch connectors
(except P5 ?oating and P8 type)
Upper limited (Solder heat resistance)
Lower limited (Solder wettability)
Temperature
2) Do not allow ?ux to spread onto the
connector leads or PC board. This may
lead to ?ux rising up to the connector
inside.
3) Touch the soldering iron to the foot
pattern. After the foot pattern and
connector terminal are heated, apply the
solder wire so it melts at the end of the
connector terminals.
Apply the solder
wire here
?ux from climbing up to the contact
surfaces, do not add more ?ux.
3) Keep the soldering iron tip temperature
below the temperature given in Table A.
200 ° C
Peak temperature 260 ° C
230 ° C
180 ° C
150 ° C
Peak temperature
220 ° C
Preheating
25 sec.
60 to 120 sec.
70 sec.
Time
Terminal
Pattern
PC board
Small angle as
possible up to
45 degrees
? Narrow-pitch connector (P5 ?oating, P8)
Temperature
245 ° C max.
155 to 165 ° C
Peak temperature
200 ° C
Preheating
60 to 120 sec.
Within 30 sec.
Time
ACCTB10E 201201-T
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e
相关PDF资料 |
PDF描述 |
|---|---|
| 770101512 | RES ARRAY 5.1K OHM 9 RES 10-SIP |
| AXN500045G | CONN SOCKET .5MM 100POS SMD |
| PS2501L-1-E3-D-A | PHOTOCOUPLER 1CH TRANS OUT SM |
| AA03-S036VA1 | CONN RCPT VERT 36POS 0.4MM GOLD |
| 770101472 | RES ARRAY 4.7K OHM 9 RES 10-SIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AXN530045G | 功能描述:板对板与夹层连接器 CONN SOCKET 30 POS 0.5mm RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| AXN530045PJ | 制造商:Panasonic Electric Works 功能描述: |
| AXN540045G | 功能描述:板对板与夹层连接器 CONN SOCKET 40 POS 0.5mm RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| AXN550045G | 功能描述:板对板与夹层连接器 CONN SOCKET 50 POS 0.5mm RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| AXN560045G | 功能描述:板对板与夹层连接器 CONN SOCKET 60 POS 0.5mm RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
发布紧急采购，3分钟左右您将得到回复。