- 您现在的位置：买卖IC网 > PDF目录6637 > AXT642124 (Panasonic Electric Works)CONN HEADER FPC .4MM 42POS SMD PDF资料下载
参数资料
| 型号： | AXT642124 |
| 厂商： | Panasonic Electric Works |
| 文件页数： | 10/11页 |
| 文件大小： | 0K |
| 描述： | CONN HEADER FPC .4MM 42POS SMD |
| 标准包装： | 1 |
| 系列： | F4S |
| 连接器类型： | 接头，中央触点带 |
| 位置数： | 42 |
| 间距： | 0.016"（0.40mm） |
| 行数： | 2 |
| 安装类型： | 表面贴装 |
| 特点： | 固定焊尾 |
| 触点表面涂层： | 金 |
| 包装： | 剪切带 (CT) |
| 配接层叠高度： | 1mm |
| 板上方高度： | 0.033"（0.84mm） |
| 配套产品： | 255-3322-1-ND - CONN SOCKET FPC .4MM 42POS SMD 255-3322-2-ND - CONN SOCKET FPC .4MM 42POS SMD |
| 其它名称： | 255-3330-1 |
Notes on Using Narrow pitch Connectors
Handling Single Components
1) Make sure not to drop or allow parts to
fall from work bench
2) Excessive force applied to the
terminals could cause warping, come
out, or weaken the adhesive strength of
the solder. Handle with care.
3) Repeated bending of the terminals
may cause terminals to break.
Cleaning ?ux from PC board
1) To increase the cleanliness of the
cleaning ?uid and cleaning operations,
prepare equipment for cleaning process
beginning with boil cleaning, ultrasonic
cleaning, and then vapor cleaning.
2) Carefully oversee the cleanliness of
the cleaning ?uids to make sure that the
contact surfaces do not become dirty
from the cleaning ?uid itself.
Storage of connectors
1) To prevent problems from voids or air
pockets due to heat of re?ow soldering,
avoid storing the connectors in areas of
high humidity. When storing the
connectors for more than six months, be
sure to consider storage area where the
humidity is properly controlled.
2) Depending on the connector type, the
color of the connector may vary from
connector to connector depending on
when it is produced.
Other Notes
1) These products are made for the
design of compact and lightweight
devices and therefore the thickness of the
molded components has been made very
thin. Therefore, be careful during
insertion and removal operations for
excessive forces applied may damage
the products.
2) Dropping of the products or rough
mishandling may bend or damage the
terminals and possibly hinder proper
re?ow soldering.
4) Do not insert or remove the connector
when it is not soldered. Forcibly applied
external pressure on the terminals can
weaken the adherence of the terminals to
the molded part or cause the terminals to
lose their evenness.
5) Excessive prying-force applied to one
end may cause product breakage and
separation of the solder joints at the
terminal.
3) Since some powerful cleaning
solutions may dissolve molded
components of the connector and wipe
off or discolor printed letters, we
recommend aqua pura electronic parts
cleaners. Please consult us if you wish to
use other types of cleaning ?uids.
4) Please note that the surfaces of
molded parts may whiten when cleaned
with alcohol.
Some connectors may change color
slightly if subjected to ultraviolet rays
during storage. This is normal and will not
affect the operation of the connector.
3) When storing the connectors with the
PC boards assembled and components
alreeady set, be careful not to stack them
up so the connectors are subjected to
excessive forces.
3) Before soldering, try not to insert or
remove the connector more than
absolutely necessary.
4) When coating the PC board after
soldering the connector to prevent the
deterioration of insulation, perform the
coating in such a way so that the coating
does not get on the connector.
5) There may be variations in the colors
of products from different production lots.
This is normal.
Excessive force applied for insertion in a
pivot action as shown may also cause
product breakage.
Align the header and socket positions
before connecting them.
Handling the PC board
? Handling the PC board after
mounting the connector
When cutting or bending the PC board
after mounting the connector, be careful
that the soldered sections are subjected
to excessive force.
The soldered areas should not be subjected to force.
4) Avoid storing the connectors in
locations with excessive dust. The dust
may accumulate and cause improper
connections at the contact surfaces.
6) The connectors are not meant to be
used for switching.
7) Be sure not to allow external pressure
to act on connectors when assembling
PCBs or moving in block assemblies.
ACCTB48E 201303-T
Panasonic Corporation
Automation Controls Business Division
industrial.panasonic.com/ac/e/
相关PDF资料 |
PDF描述 |
|---|---|
| V23054D1026F104 | RELAY GEN PURPOSE DPDT 5A 60V |
| AXK744147G | CONN SOCKET BRD/BRD .4MM 44POS |
| PRD-11AG0-277 | RELAY GEN PURPOSE DPDT 30A 277V |
| 009158020025001 | CONN STACKING 2.1MM-2.7MM 20POS |
| 3-179608-0 | CONN DBL ROW HOLDER MT 30POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AXT642124DD1 | 功能描述:FFC & FPC连接器 Connector RoHS:否 制造商:JAE Electronics 产品类型:Plugs 系列:HD 节距:0.5 mm 位置/触点数量:40 安装角: 安装风格:Cable 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:100 V per contact 电流额定值:0.24 A to 1 A |
| AXT644124 | 功能描述:FFC & FPC连接器 CONN HEADER FPC 44 POS 0.4mm RoHS:否 制造商:JAE Electronics 产品类型:Plugs 系列:HD 节距:0.5 mm 位置/触点数量:40 安装角: 安装风格:Cable 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:100 V per contact 电流额定值:0.24 A to 1 A |
| AXT646124 | 功能描述:FFC & FPC连接器 CONN HEADER 46 POS 0.4mm RoHS:否 制造商:JAE Electronics 产品类型:Plugs 系列:HD 节距:0.5 mm 位置/触点数量:40 安装角: 安装风格:Cable 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:100 V per contact 电流额定值:0.24 A to 1 A |
| AXT648124 | 功能描述:FFC & FPC连接器 CONN HEADER 48 POS 0.4mm RoHS:否 制造商:JAE Electronics 产品类型:Plugs 系列:HD 节距:0.5 mm 位置/触点数量:40 安装角: 安装风格:Cable 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:100 V per contact 电流额定值:0.24 A to 1 A |
| AXT648124DD1 | 制造商:Panasonic Electric Works 功能描述:F4S 48PINS HEADER |
发布紧急采购，3分钟左右您将得到回复。