- 您现在的位置：买卖IC网 > PDF目录253950 > AZ5101429 SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 8.1mm, PANEL MOUNT PDF资料下载
参数资料
| 型号： | AZ5101429 |
| 元件分类： | 开关 |
| 英文描述： | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 8.1mm, PANEL MOUNT |
| 文件页数： | 7/22页 |
| 文件大小： | 694K |
| 代理商： | AZ5101429 |
8
α
Vmax (m/s)
CAUTIONS FOR USE
Pay attention to the following points
when designing the dog for limit switch
operation.
1. Make the dog faceplate as smooth
as possible.
2. Adjust both the dog angle and the
set arm angle as below, depending on
the operating speed.
3. The depth (h) of the dog effects the
lifespan of the limit switch. Therefore,
set the depth to a maximum of 80% of
the Total Travel (T.T.)
4. The relationship between the speed
of the dog (V = m/s) and the tip angle
(
α) is as follows:
1) V&0.2m/s
3) 0.5m/s ! V&2m/s
Because the arm jiggle is as a mini-
mum at a comparative speed such as
V&0.5m/s, setting both the dog angle
so that it travels perpendicularly and
the arm angle to 45° is optimum.
If overriding the dog, set the arm per-
pendicularly, so that
α =45°. If the dog
angle is reduced, the tolerable speed
is increased.
5) Roller plunger type
DESIGN OF OPERATING DOG AND OPERATING SPEED
When V&0.2m/s, set the arm to per-
pendicular and set the arm rise angle
to between 45° and 90°. If the dog rise
angle is reduced, the maximum tolera-
ble speed is increased.
As a rule,
α = 45° is optimum.
2) V&0.5m/s
The maximum tolerable speed can be
extended by further reducing the dog
rise angle from 45° when 0.5m/s !
V&2m/s. It is necessary to set the arm
so that the dog’s cutting surfaces are
always parallel (
θ o = 90°– α)
4) Overriding the dog (V&0.2m/s)
h
V
α = 45° to 90°
F
o
h
α
V
θ
F
h
V
α = 45°
o = 45
°
θ
h
α
h
α
45°
0.2
60°
0.1
60 to 90°
0.05
α
Vmax (m/s)
Even if overriding the dog, set the for-
wards and rearwards motion exactly
the same, and avoid any settings that
make the actuator accelerate rapidly
from the dog.
5. Operation speed
1) When the operation (acting and
reverting) speed is exceedingly slow,
switching of the contacts will become
unstable and this could cause prob-
lems such as failure to make contact
and welding. As a guide, the speed
should be at least 1mm/s.
2) When the operation (acting and
reverting) speed is exceedingly fast,
be careful because the violent motion
could cause breakage and with
increased frequency, contact switching
will not be able to keep up. As a guide,
the switching frequency should be
within 20 times per minute.
20°
0.5
30°
0.25
h
(0.5 to 0.7) T.T.
(0.6 to 0.8) T.T.
α
Vmax (m/s)
45°
0.2
60°
0.1
60 to 90°
0.05
α
Vmax (m/s)
40°
0.7
35°
0.9
30°
1.3
25°
2.0
相关PDF资料 |
PDF描述 |
|---|---|
| AZ5101F | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 0.8A, 125VDC, 8.1mm, PANEL MOUNT |
| AZ7430 | SNAP ACTING/LIMIT SWITCH, DPDT, MOMENTARY, 0.4A, 115VDC, 8.5mm, PANEL MOUNT |
| AZ5104 | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 0.8A, 125VDC, PANEL MOUNT |
| AZ51051629 | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 6A, 24VDC, PANEL MOUNT |
| AZ51056629 | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 6A, 24VDC, PANEL MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AZ51019 | 制造商:Panasonic Electric Works 功能描述: |
| AZ5104 | 制造商:Panasonic Electric Works 功能描述:Switch Limit N.O./N.C. SPDT Side Roller Arm Conduit 10A 500VAC 125VDC 13.34N Rotary Screw Mount |
| AZ51049 | 制造商:Panasonic Electric Works 功能描述: |
| AZ51059 | 制造商:Panasonic Industrial Devices 功能描述:Yoke Standard Type Vertical Limit Switch 制造商:Panasonic Electric Works 功能描述: |
| AZ5106 | 制造商:ABUS August Bremicker Sohne KG 功能描述: |
发布紧急采购，3分钟左右您将得到回复。