- 您现在的位置：买卖IC网 > PDF目录18438 > B32021A3102M289 (EPCOS Inc)FILM CAP 1.0 NF 20% 300VAC MKPY2 PDF资料下载
参数资料
| 型号： | B32021A3102M289 |
| 厂商： | EPCOS Inc |
| 文件页数： | 13/21页 |
| 文件大小： | 0K |
| 描述： | FILM CAP 1.0 NF 20% 300VAC MKPY2 |
| 标准包装： | 1,000 |
| 系列： | B32021 |
| 电容： | 1000pF |
| 额定电压 - AC： | * |
| 额定电压 - DC： | * |
| 电介质材料： | 聚丙烯 |
| 容差： | ±20% |
| ESR（等效串联电阻）： | * |
| 工作温度： | -40°C ~ 110°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 径向 |
| 尺寸/尺寸： | 0.512" L x 0.158" W（13.00mm x 4.00mm） |
| 高度 - 座高（最大）： | 0.354"（9.00mm） |
| 端子： | PC 引脚 |
| 引线间隔： | 0.394"（10.00mm） |
| 特点： | EMI 抑制 |
| 应用： | * |
| 包装： | 带盒（TB） |
B32021 ... B32026
Y2 / 300 V AC
1.3
General notes on soldering
Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-
gory temperature T max . Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
The overheating associated with some of these factors can usually be reduced by suitable coun-
termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Pre-heating with a maximum temperature of 110 ° C
Temperature inside the capacitor should not exceed the following limits:
MKP/MFP 110 ° C
MKT 160 ° C
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled af-
ter the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
Uncoated capacitors
For uncoated MKT capacitors with lead spacings ≤ 10 mm (B32560/B32561) the following mea-
sures are recommended:
pre-heating to not more than 110 ° C in the preheater phase
rapid cooling after soldering
Application note for X1 / X2 EMI capacitors
Please read Cautions and warnings and
Important notes at the end of this document.
Page 13 of 21
相关PDF资料 |
PDF描述 |
|---|---|
| B32021A3102M189 | FILM CAP 1.0NF 20% 300VAC MKP |
| NTF3055L175T1G | MOSFET N-CH 60V 2A SOT223 |
| ASG-D-V-B-1.500GHZ-T | OSC 1.500 GHZ 2.5V LVDS SMD |
| CM309S29.500MABJTR | CRYSTAL 29.500 MHZ 18PF SMD |
| SRF1006-402Y | INDUCTOR COMMN MODE 4000UH 0.30A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| B32021A3103 | 制造商:EPCOS 制造商全称:EPCOS 功能描述:EMI Suppression Capacitors (MKP) |
| B32021A3103M | 功能描述:薄膜电容器 0.01uF 300volts 20% Y2 RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32021A3103M000 | 制造商:TDK Epcos 功能描述:Cap Film Suppression Y2 0.01uF 300VAC PP 20% (13 X 6 X 12mm) Radial 10mm 110 C Bulk |
| B32021A3103M026 | 制造商:TDK-EPC 功能描述:FILM CAP 10 NF 20% 300VAC MKPY2 - Bulk |
| B32021A3103M189 | 制造商:TDK-EPC 功能描述:FILM CAP 10 NF 20% 300V MKPY2 - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。