- 您现在的位置：买卖IC网 > PDF目录18240 > B32674F4225K (EPCOS Inc)FILM CAP 2.2UF 10% 450V MKP PDF资料下载
参数资料
| 型号： | B32674F4225K |
| 厂商： | EPCOS Inc |
| 文件页数： | 16/22页 |
| 文件大小： | 0K |
| 描述： | FILM CAP 2.2UF 10% 450V MKP |
| 标准包装： | 280 |
| 系列： | B32674 |
| 电容： | 2.2µF |
| 额定电压 - DC： | 450V |
| 电介质材料： | 聚丙烯，金属化 |
| 容差： | ±10% |
| ESR（等效串联电阻）： | * |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 径向 |
| 端子： | PC 引脚 |
| 引线间隔： | 1.083"（27.50mm） |
| 特点： | 交流和双倍脉冲 |
| 包装： | 散装 |
| 其它名称： | B32674F4225K000 |
B32674 ... B32678
MKP DC link
high power series
1.3
General notes on soldering
Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-
gory temperature T max . Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
The overheating associated with some of these factors can usually be reduced by suitable coun-
termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Pre-heating with a maximum temperature of 110 ° C
Temperature inside the capacitor should not exceed the following limits:
MKP/MFP 110 ° C
MKT 160 ° C
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled af-
ter the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
Uncoated capacitors
For uncoated MKT capacitors with lead spacings ≤ 10 mm (B32560/B32561) the following mea-
sures are recommended:
pre-heating to not more than 110 ° C in the preheater phase
rapid cooling after soldering
Please read Cautions and warnings and
Important notes at the end of this document.
Page 16 of 22
相关PDF资料 |
PDF描述 |
|---|---|
| M2024BB1W01 | SW TOGGLE SP3T THR SILV SLD LUG |
| FXO-PC725-125 | OSC 125 MHZ 2.5V PECL SMD |
| FXO-PC725-150 | OSC 150 MHZ 2.5V PECL SMD |
| MLW3012-28-PB-1A | SWITCH ROCKER SPDT 5A 125V |
| FXO-PC725-155.52 | OSC 155.52 MHZ 2.5V PECL SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| B32674F4225K000 | 功能描述:薄膜电容器 2.2UF 10% 450V FILM CAP MKP BOXED RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32674F4475K | 功能描述:薄膜电容器 Film Cap 4,7UF 10% 450V MKP BOXED RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32674F4475K000 | 功能描述:薄膜电容器 4.7UF 10% 450V FILM CAP MKP BOXED RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32674F6105K | 功能描述:薄膜电容器 1.0uF 630volts 10% RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32674F6105K000 | 功能描述:CAP FILM 1UF 10% 800VDC RADIAL 制造商:epcos (tdk) 系列:B32674 包装:散装 零件状态:在售 电容:1μF 容差:±10% 额定电压 - AC:- 额定电压 - DC:800V 介电材料:聚丙烯（PP），金属化 工作温度:-40°C ~ 105°C 安装类型:通孔 封装/外壳:径向 高度 - 安装（最大值）:- 端接:PC 引脚 引线间距:1.083"（27.50mm） 应用:DC 链路，DC 滤波 等级:- 特性:长寿命 标准包装:1,280 |
发布紧急采购，3分钟左右您将得到回复。