- 您现在的位置：买卖IC网 > PDF目录18209 > B32676E6475J (EPCOS Inc)FILM CAP 4.7UF 5% 630V MKP PDF资料下载
参数资料
| 型号： | B32676E6475J |
| 厂商： | EPCOS Inc |
| 文件页数： | 16/22页 |
| 文件大小： | 0K |
| 描述： | FILM CAP 4.7UF 5% 630V MKP |
| 产品培训模块： | Film Capacitors |
| 产品目录绘图： | B32zzz(D,E,T) Series Side 1 B32zzz(D,E,T) Series Side 2 |
| 标准包装： | 180 |
| 系列： | B32676 |
| 电容： | 4.7µF |
| 额定电压 - DC： | 630V |
| 电介质材料： | 聚丙烯，金属化 |
| 容差： | ±5% |
| ESR（等效串联电阻）： | * |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 径向 |
| 端子： | PC 引脚 |
| 引线间隔： | 1.476"（37.50mm） |
| 特点： | 交流和双倍脉冲 |
| 包装： | 散装 |
| 其它名称： | B32676E6475J000 |
B32674 ... B32678
MKP DC link
high power series
1.3
General notes on soldering
Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-
gory temperature T max . Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
The overheating associated with some of these factors can usually be reduced by suitable coun-
termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Pre-heating with a maximum temperature of 110 ° C
Temperature inside the capacitor should not exceed the following limits:
MKP/MFP 110 ° C
MKT 160 ° C
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled af-
ter the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
Uncoated capacitors
For uncoated MKT capacitors with lead spacings ≤ 10 mm (B32560/B32561) the following mea-
sures are recommended:
pre-heating to not more than 110 ° C in the preheater phase
rapid cooling after soldering
Please read Cautions and warnings and
Important notes at the end of this document.
Page 16 of 22
相关PDF资料 |
PDF描述 |
|---|---|
| B32774D705J | FILM CAP 7UF 5% 1100V MKP |
| B32522C1335K189 | FILM CAP 3.3000UF 10% 100V |
| 7A-20.000MBBK-T | CRYSTAL 20.000 MHZ 20PF SMD |
| B32686A1104J | FILM CAP 0.100UF 5% 1600V |
| FVXO-PC73BR-742.4347 | OSC 742.4347 MHZ 3.3V PECL SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| B32676E6475J000 | 功能描述:薄膜电容器 4.7UF 5% 630V FILM CAP MKP BOXED RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32676E6475K | 功能描述:薄膜电容器 4.7uF 630volts 10% 37.5mmL/S 1.0mmL/D RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32676E6475K000 | 制造商:EPCOS 功能描述:Cap Film 4.7uF 630V PP 10% (42 X 18 X 32.5mm) Radial 37.5mm 100 制造商:EPCOS 功能描述:Cap Film 4.7uF 630V PP 10% (42 X 18 X 32.5mm) Radial 37.5mm 100°C Bulk |
| B32676E6685K | 功能描述:薄膜电容器 6.8uF 630volts 10% 37.5mmL/S 1.0mmL/D RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32676E6755K | 功能描述:薄膜电容器 7.5uF 630volts 10% 37.5mmL/S 1.0mmL/D RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
发布紧急采购，3分钟左右您将得到回复。