- 您现在的位置：买卖IC网 > Datasheet目录840 > B32686A2104J (EPCOS Inc)FILM CAP 0.1000UF 5% 2000V Datasheet资料下载
参数资料
| 型号： | B32686A2104J |
| 厂商： | EPCOS Inc |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | FILM CAP 0.1000UF 5% 2000V |
| 标准包装： | 32 |
| 系列： | B32686 |
| 电容： | 0.1µF |
| 额定电压 - AC： | 500V |
| 额定电压 - DC： | 2000V（2kV） |
| 电介质材料： | 聚丙烯，金属化 |
| 容差： | ±5% |
| 工作温度： | -55°C ~ 110°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 径向 |
| 尺寸/尺寸： | 1.654" L x 0.787" W（42.00mm x 20.00mm） |
| 高度 - 座高（最大）： | 1.555"（39.50mm） |
| 端子： | PC 引脚 |
| 引线间隔： | 1.476"（37.50mm） |
| 特点： | 交流和双倍脉冲 |
| 包装： | 散装 |
| 其它名称： | B32686A2104J000 |
B32686A
Very high pulse (wound)
1.3
General notes on soldering
Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-
gory temperature T max . Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
The overheating associated with some of these factors can usually be reduced by suitable coun-
termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Pre-heating with a maximum temperature of 110 ° C
Temperature inside the capacitor should not exceed the following limits:
MKP/MFP 110 ° C
MKT 160 ° C
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled af-
ter the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
Uncoated capacitors
For uncoated MKT capacitors with lead spacings ≤ 10 mm (B32560/B32561) the following mea-
sures are recommended:
pre-heating to not more than 110 ° C in the preheater phase
rapid cooling after soldering
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| B32686S2473K563 | FILM CAP 0.0470UF 10% 2000V MFP |
| B32778G0406K | CAP FILM 40UF 1.1KVDC RADIAL |
| B32798G8306K | CAP FILM 30UF 875VDC RADIAL |
| B32916A3685K | CAP FILM 6.8UF 760VDC RADIAL |
| B32924B2155K | CAP FILM 1.5UF 310VAC RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| B32686A2104K | 功能描述:薄膜电容器 0.1uF 2KV 10% RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32686A2223J | 功能描述:薄膜电容器 0.022uF 2KV 5% RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32686A224K | 功能描述:薄膜电容器 0.22uF 1KV 10% RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32686A2333J | 功能描述:薄膜电容器 0.033uF 2KV 5% RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32686A2473J | 功能描述:薄膜电容器 0.047uF 2KV 5% RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
发布紧急采购，3分钟左右您将得到回复。