- 您现在的位置：买卖IC网 > PDF目录18175 > B32912A4103K (EPCOS Inc)FILM CAP 10NF 10% 440VAC PDF资料下载
参数资料
| 型号： | B32912A4103K |
| 厂商： | EPCOS Inc |
| 文件页数： | 11/19页 |
| 文件大小： | 0K |
| 描述： | FILM CAP 10NF 10% 440VAC |
| 标准包装： | 1,000 |
| 系列： | B32912 |
| 电容： | 10000pF |
| 额定电压 - AC： | 440V |
| 电介质材料： | 聚丙烯，金属化 |
| 容差： | ±10% |
| 工作温度： | -40°C ~ 110°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 径向 |
| 端子： | PC 引脚 |
| 引线间隔： | 0.591"（15.00mm） |
| 特点： | EMI 抑制 |
| 应用： | * |
| 包装： | 散装 |
| 其它名称： | B32912A4103K000 |
B32911 ... B32916
X1 / 330 V AC
1.3
General notes on soldering
Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-
gory temperature T max . Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
The overheating associated with some of these factors can usually be reduced by suitable coun-
termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Pre-heating with a maximum temperature of 110 ° C
Temperature inside the capacitor should not exceed the following limits:
MKP/MFP 110 ° C
MKT 160 ° C
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled af-
ter the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
Uncoated capacitors
For uncoated MKT capacitors with lead spacings ≤ 10 mm (B32560/B32561) the following mea-
sures are recommended:
pre-heating to not more than 110 ° C in the preheater phase
rapid cooling after soldering
Application note for X1 / X2 EMI capacitors
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 19
相关PDF资料 |
PDF描述 |
|---|---|
| M2023SS1W01-BG | SW TOGGLE DPDT BAT THR SLV SLD |
| CG36.5101.151 | MOD PWR 4A STD FILTER QC PNL MNT |
| FXO-PC726-62.5 | OSC 62.5 MHZ 2.5V PECL SMD |
| B32522Q8334K | FILM CAP 0.33UF 10% 630V |
| IXFH15N100 | MOSFET N-CH 1000V 15A TO-247 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| B32912A4103K000 | 功能描述:薄膜电容器 10NF 10% 440V FILMCAP MKP X1 LS 15 RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32912A4103M | 功能描述:薄膜电容器 0.01uF 440volts 20% X1 RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32912A4103M189 | 功能描述:薄膜电容器 0.01uF 440volts 20% X1 RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32912A4103M289 | 功能描述:薄膜电容器 0.01uF 440volts 20% X1 RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
| B32912A4153K | 功能描述:薄膜电容器 Film Cap 15NF 10% 440VAC MKP X1 L.S. 15 RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm |
发布紧急采购，3分钟左右您将得到回复。