参数资料
| 型号： | B384F120T30 |
| 厂商： | Vicor Corporation |
| 文件页数： | 6/12页 |
| 文件大小： | 0K |
| 描述： | CONVERTER BUS BCM 12V 300W SMD |
| 应用说明： | Factorized Power Architecture and V-I Chips |
| 产品培训模块： | VI Chip Bus Converter Modules |
| 标准包装： | 1 |
| 系列： | V-I Chip™, BCM™ |
| 类型： | 总线转换器模块 |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 360V |
| 电压 - 输入（最大）： | 400V |
| 输出电压： | 12V |
| 电流 - 输出（最大）： | 25A |
| 电源（瓦） - 制造商系列： | 300W |
| 电压 - 隔离： | 4.242kV（4242V） |
| 应用： | 商用 |
| 特点： | 具有远程开/关功能和 UVLO |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 模块 |
| 尺寸/尺寸： | 1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） |
| 包装： | 托盘 |
| 工作温度： | -40°C ~ 125°C |
| 效率： | 95.3% |
| 电源（瓦特）- 最大： | 300W |
| 重量： | 0.033 磅（14.97g） |
| 其它名称： | 1102-1015 |
Pin / Control Functions
+In / -In – DC Voltage Input Ports
The V?I Chip input voltage range should not be exceeded. An internal
under / over voltage lockout-function prevents operation outside of the
normal operating input range. The BCM turns on within an input voltage
4
3
2
1
window bounded by the “Input under-voltage turn-on” and “Input over-
voltage turn-off” levels, as specified. The V?I Chip may be protected
against accidental application of a reverse input voltage by the addition
of a rectifier in series with the positive input, or a reverse rectifier in
shunt with the positive input located on the load side of the input fuse.
The connection of the V?I Chip to its power source should be
implemented with minimal distribution inductance. If the interconnect
inductance exceeds 100 nH, the input should be bypassed with a RC
damper to retain low source impedance and stable operation. With an
interconnect inductance of 200 nH, the RC damper may be 2.2 μF in
series with 0.3 ? . A single electrolytic or equivalent low-Q capacitor may
be used in place of the series RC bypass.
+Out
-Out
+Out
-Out
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
A
B
C
D
E
H
J
K
L
M
N
P
R
T
+In
TM
RSV
PC
-In
PC – Primary Control
The Primary Control port is a multifunction node that provides the
following functions:
Bottom View
Enable / Disable – If the PC port is left floating, the BCM output is
enabled. Once this port is pulled lower than 2.4 Vdc with respect to
–In, the output is disabled. This action can be realized by employing
a relay, opto-coupler, or open collector transistor. Refer to Figures 1-
3, 12 and 13 for the typical enable / disable characteristics. This port
should not be toggled at a rate higher than 1 Hz. The PC port should
also not be driven by or pulled up to an external voltage source.
Primary Auxiliary Supply – The PC port can source up to 2.4 mA at
5.0 Vdc. The PC port should never be used to sink current.
Alarm – The BCM contains circuitry that monitors output overload,
input over voltage or under voltage, and internal junction
temperatures. In response to an abnormal condition in any of the
monitored parameters, the PC port will toggle. Refer to Figure 13
for PC alarm characteristics.
TM and RSV – Reserved for factory use.
+Out / -Out – DC Voltage Output Ports
Two sets of contacts are provided for the +Out port. They must be
connected in parallel with low interconnect resistance. Similarly, two sets
of contacts are provided for the –Out port. They must be connected in
parallel with low interconnect resistance. Within the specified operating
range, the average output voltage is defined by the Level 1 DC behavioral
model of Figure 21. The current source capability of the BCM is rated in
the specifications section of this document.
The low output impedance of the BCM reduces or eliminates the need
for limited life aluminum electrolytic or tantalum capacitors at the input
of POL converters.
Total load capacitance at the output of the BCM should not exceed the
specified maximum. Owing to the wide bandwidth and low output
impedance of the BCM, low frequency bypass capacitance and
significant energy storage may be more densely and efficiently provided
by adding capacitance at the input of the BCM.
Signal
Name
+In
–In
TM
RSV
PC
+Out
–Out
Figure 14 — BCM pin configuration
Designation
A1-E1, A2-E2
L1-T1, L2-T2
H1, H2
J1, J2
K1, K2
A3-D3, A4-D4,
J3-M3, J4-M4
E3-H3, E4-H4,
N3-T3, N4-T4
vicorpower.com
800-735-6200
V?I Chip Bus Converter
B384F120T30
Rev. 2.4
Page 6 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| B048F240T30 | CONVERTER BUS 24V OUT 300W SMD |
| MS27468T21B11A | CONN HSG RCPT 11POS JAMNUT PINS |
| VE-24D-MV-F2 | CONVERTER MOD DC/DC 85V 150W |
| M83723/91W2212NLC | CONN HSG PLUG 12POS STRGHT SCKT |
| VE-24D-MV-F1 | CONVERTER MOD DC/DC 85V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| B384F120T30_10 | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:Bus Converter |
| B384F120T30-EB | 功能描述:HV BCM BUS CONVERTER EVAL BOARD RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:V-I Chip™, BCM™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| B384T120T30 | 功能描述:HV BCM BUS CONVERT 12V 300W RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, BCM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g） |
| B3850 | 制造商:EPCOS 制造商全称:EPCOS 功能描述:SAW Components Low-Loss Filter 125,00 MHz |
| B3851 | 制造商:EPCOS 制造商全称:EPCOS 功能描述:SAW Components Low-Loss Filter for Mobile Communication 881,50 MHz |
发布紧急采购，3分钟左右您将得到回复。