- 您现在的位置：买卖IC网 > PDF目录13093 > BA033CC0T (Rohm Semiconductor)IC REG LDO 3.3V 1A TO220FP PDF资料下载
参数资料
| 型号： | BA033CC0T |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 15/23页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V 1A TO220FP |
| 标准包装： | 500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 4 V ~ 25 V |
| 电压 - 压降（标准）： | 0.3V @ 500mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1A（最小值） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | TO-220-3 整包 |
| 供应商设备封装： | TO-220FP |
| 包装： | 管件 |
| 产品目录页面： | 1369 (CN2011-ZH PDF) |
BAxxDD0xx BAxxCC0xx
Datasheet
● Operational Notes
1) Protection Circuits
Over-current Protection Circuit
A built-in over-current protection circuit corresponding to the current capacity prevents the destruction of the IC when there
are load shorts. This protection circuit is a “7”-shaped current control circuit that is designed such that the current is restricted
and does not latch even when a large current momentarily flows through the system with a high-capacitance capacitor.
However, while this protection circuit is effective for the prevention of destruction due to unexpected accidents, it is not
suitable for continuous operation or transient use. Please be aware when creating thermal designs that the overcurrent
protection circuit has negative current capacity characteristics with regard to temperature (Refer to Fig.6 and 18).
Thermal Shutdown Circuit (Thermal Protection)
This system has a built-in temperature protection circuit for the purpose of protecting the IC from thermal damage.
As shown above, this must be used within the range of acceptable loss, but if the acceptable loss happens to be
continuously exceeded, the chip temperature Tj increases, causing the temperature protection circuit to operate.
When the thermal shutdown circuit operates, the operation of the circuit is suspended. The circuit resumes operation
immediately after the chip temperature Tj decreases, so the output repeats the ON and OFF states (Please refer to
Fig.14 and 26 for the temperatures at which the temperature protection circuit operates).
There are cases in which the IC is destroyed due to thermal runaway when it is left in the overloaded state. Be sure to
avoid leaving the IC in the overloaded state.
Reverse Current
In order to prevent the destruction of the IC when a reverse current flows through the IC, it is recommended that a diode
be placed between the Vcc and Vo and a pathway be created so that the current can escape (Refer to Fig.35).
Reverse current
Vcc
CTL
GND
OUT
Fig.35 Bypass diode
2) This IC is bipolar IC that has a P-board (substrate) and P+ isolation layer between each devise, as shown in Fig.36. A
P-N junction is formed between this P-layer and the N-layer of each device, and the P-N junction operates as a parasitic
diode when the electric potential relationship is GND> Pin A, GND> Pin B, while it operates as a parasitic transistor when
the electric potential relationship is Pin B GND> Pin A. Parasitic devices are structurally inevitable in the IC. The
operation of parasitic devices induces mutual interference between circuits, causing malfunctions and eventually the
destruction of the IC. It is necessary to be careful not to use the IC in ways that would cause parasitic elements to
operate. For example, applying a voltage that is lower than the GND (P-board) to the input terminal.
Transistor (NPN)
(Pin A)
Resistor
(Pin B)
C
B
E
(Pin B)
B
C
GND
E
N
P+
N
P
P+
N
N
P+
N
N
P
P+
N
GND
Parasitic element
or transistor
P
Parasitic element
P
(Pin A)
GND
Parasitic element
or transistor
GND
Parasitic element
GND
Fig.36 Example of the basic structure of a bipolar IC
Status of this document
The Japanese version of this document is formal specification. A customer may use this translation version only for a reference
to help reading the formal version.
If there are any differences in translation version of this document formal version takes priority.
www.rohm.com
? 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
15/20
TSZ02201-0R6R0A600130-1-2
9.Aug.2013 Rev.003
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JWZ-EZ-B1 | CONVERTER MOD DC/DC 2V 10W |
| VI-B54-EU-F3 | CONVERTER MOD DC/DC 48V 200W |
| VI-JWY-EZ-B1 | CONVERTER MOD DC/DC 3.3V 16.5W |
| VI-JWX-EZ-B1 | CONVERTER MOD DC/DC 5.2V 25W |
| TC1185-2.7VCT713 | IC REG LDO 2.7V .15A SOT23A-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BA033CC0WFP | 制造商:ROHM 制造商全称:Rohm 功能描述:Standard Fixed Output LDO Regulators |
| BA033CC0WFP-E2 | 功能描述:低压差稳压器 - LDO REG 1A 3.3V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| BA033CC0WT | 功能描述:低压差稳压器 - LDO REG 1A 3.3V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| BA033CC0WT-V5 | 功能描述:低压差稳压器 - LDO LDO REG 3.3V 1A 5PIN RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| BA033FE2 | 制造商:ROHM Semiconductor 功能描述: |
发布紧急采购，3分钟左右您将得到回复。