- 您现在的位置：买卖IC网 > PDF目录295137 > BA15DD0T-E2 1.5 V FIXED POSITIVE LDO REGULATOR, 0.7 V DROPOUT, SFM3 PDF资料下载
参数资料
| 型号： | BA15DD0T-E2 |
| 元件分类： | 固定正电压单路输出LDO稳压器 |
| 英文描述： | 1.5 V FIXED POSITIVE LDO REGULATOR, 0.7 V DROPOUT, SFM3 |
| 封装： | LEAD FREE, TO-220FP, 3 PIN |
| 文件页数： | 6/9页 |
| 文件大小： | 1047K |
| 代理商： | BA15DD0T-E2 |
6/8
Fig.30 shows the acceptable loss and heat reducing characteristics of the TO220FP package The portion shown by the
diagonal line is the acceptable loss range that can be used with the IC alone. Even when the ambient temperature Ta is a normal
temperature (25℃), the chip (junction) temperature Tj may be quite high so please operate the IC at temperatures less than the
acceptable loss Pd.
The method of calculating the power consumption Pc(W) is as follows.
Pc = (Vcc-Vo) × Io
＋ Vcc × Icca
Acceptable loss Pd≦Pc
Solving this for load current IO in order to operate within the acceptable loss:
Io≦
（Please refer to Figs.8 and 20 for Icca.）
It is then possible to find the maximum load current IoMAX with respect to the applied voltage Vcc at the time of thermal design.
·Calculation Example
Example 1) When Ta=85℃, Vcc=8.3V, Vo=3.3V, BA33DD0WT
Io≦
With the IC alone : θja=62.5℃/W → -16mW/℃
Io≦200mA (Icca : 2mA)
25℃=2000mW → 85℃=1040mW
Please refer to the above information and keep thermal designs within the scope of acceptable loss for all operating
temperature ranges.
The power consumption Pc of the IC when there is a short circuit (short between Vo and GND) is :
Pc=Vcc×(Icca＋Ishort)
＊Ishort : Short circuit current
●Peripheral Circuit Considerations
·Vcc Terminal
Please attach a capacitor (greater than 0.33μF) between the Vcc and GND
.
The capacitance values will differ depending on the application, so please take this into account when configuring the
terminal.
·GND Terminal
Please be sure to keep the set ground and IC ground at the same potential level so that a potential difference does not arise
between them.
If a potential difference arises between the set ground and the IC ground, the preset voltage will not be outputted, causing
the system to become unstable. Therefore, please reduce the impedance by making the ground patterns as wide as
possible and by reducing the distance between the set ground and the IC ground as much as possible.
·CTL Terminal
The CTL terminal is turned ON at 2.0V and higher and OFF at 0.8V and lower within the operating power supply voltage
range.
The power supply and the CTL terminal may be started up and shut down in any order without problems.
●Vo Terminal
Fig.32 Output Equivalent Circuit
Fig.33 ESR-Io Characteristics
Fig.34 ESR vs Io Characteristics
(BA□□CC0,22μF)
（BA□□DD0,22μF）
Please attach an anti-oscillation capacitor between Vcc and GND. The capacitance of the capacitor may significantly change
due to factors such as temperature changes, making it impossible to completely stop oscillations. Please use a tantalum
capacitor or aluminum electrolysis capacitor with favorable characteristics and small internal series resistance (ESR) even at
low temperatures. The output fluctuates regardless of whether the ESR is large or small. Please use the IC within the stable
operating region while referring to the ESR characteristics reference data shown in Figs.32 through 34. In applications where
there are sudden load fluctuations, the use of a capacitor with large capacitance is recommended.
Below figure , it is ESR-to-Io stability Area characteristics ,measured by 22μＦ-ceramic-capacitor and resistor connected in
series.
This characteristics is
not
equal value perfectly
to 22μＦ-aluminum electrolytic capacitor in order to measurement
method.
Note, however, that the stable range suggested in the figure depends on the IC and the resistance load involved, and can vary
with the board’s wiring impedance, input impedance, and/or load impedance. Therefore, be certain to ascertain the final status
of these items for actual use.
Keep capacitor capacitance within a range of 22μF～1000μF. It is also recommended that a 0.33μF bypass capacitor be
connected as close to the input pin-GND as location possible. However, in situations such as rapid fluctuation of the input
voltage or the load, please check the operation in real application to determine proper capacitance.
Pd – Vcc×Icca
Vcc－Vo
1.04－8.3×Icca
5
200
400
800
1000
0.1
1
10
Stable operating region
100
0
600
Unstable operating region
1
0.1
1
10
100
10
100
1000
OUTPUT
CURRENT：lo(mA)
OUTPUT
CURRENT：lo(mA)
Unstable operating region
Stable operating region
EF
F
E
CT
IV
E
S
E
RI
ES
R
E
SI
ST
ANC
E
:ESR
[Ω
]
EF
F
E
CT
IV
E
S
E
RI
ES
R
E
SI
ST
ANC
E
:ESR
[Ω
]
OUT
22μF
IC
Vcc：
Vo：
Io：
Icca：
Input voltage
Output voltage
Load current
Circuit current
相关PDF资料 |
PDF描述 |
|---|---|
| BA15DD0T-TR | 1.5 V FIXED POSITIVE LDO REGULATOR, 0.7 V DROPOUT, SFM3 |
| BA15DD0WHFP-E2 | 1.5 V FIXED POSITIVE LDO REGULATOR, 0.7 V DROPOUT, PSSO5 |
| BA15DD0WT-E2 | 1.5 V FIXED POSITIVE LDO REGULATOR, 0.7 V DROPOUT, SFM5 |
| BA15DD0WT-TR | 1.5 V FIXED POSITIVE LDO REGULATOR, 0.7 V DROPOUT, SFM5 |
| BA08CC0T-E2 | 8 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, SFM3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BA15DD0WHFP | 制造商:ROHM 制造商全称:Rohm 功能描述:Standard Fixed Output LDO Regulators |
| BA15DD0WHFP-TR | 功能描述:IC REG LDO 1.5V 2A HRP5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.7V 输入电压:最高 5.5V 电压 - 压降（标准）:0.21V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:剪切带 (CT) 产品目录页面:1100 (CN2011-ZH PDF) 其它名称:576-1852-1 |
| BA15DD0WT | 功能描述:低压差稳压器 - LDO LDO REG 1.5V 2A 5PIN RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| BA15DXXX | 制造商:ALTECH 制造商全称:Altech corporation 功能描述:30 mm Replacment Filament Bulbs |
| BA-15E15UD | 制造商:未知厂家 制造商全称:未知厂家 功能描述:LED LIGHT BAR & BAR GRAPH ARRAYS |
发布紧急采购，3分钟左右您将得到回复。