参数资料
| 型号： | BA33BC0WT |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 10/19页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V 1A TO220FP-5 |
| 特色产品： | CMOS LDO Regulators |
| 标准包装： | 500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 16V |
| 电压 - 压降（标准）： | 0.3V @ 200mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1A（最小值） |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 通孔 |
| 封装/外壳： | TO-220-5 整包 |
| 供应商设备封装： | TO-220FP-5 |
| 包装： | 管件 |
| 产品目录页面： | 1368 (CN2011-ZH PDF) |
BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5
Datasheet
● Operational Notes
1. Absolute maximum ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break
down the devices, thus making impossible to identify breaking mode, such as a short circuit or an open circuit. If any over rated
values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as fuses.
2. GND voltage
The potential of GND pin must be minimum potential in all operating conditions.
3. Thermal design
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating
conditions.
4. Inter-pin shorts and mounting errors
Use caution when positioning the IC for mounting on printed circuit boards.
The IC may be damaged if there is any connection error or if pins are shorted together.
5. Actions in strong electromagnetic field
Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to
malfunction.
6. Testing on application boards
When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress.
Always discharge capacitors after each process or step. Always turn the IC's power supply off before connecting it to or
removing it from a jig or fixture during the inspection process. Ground the IC during assembly steps as an antistatic
measure. Use similar precaution when transporting or storing the IC.
7. Regarding input pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated.
P-N junctions are formed at the intersection of these P layers with the N layers of other elements, creating a parasitic
diode or transistor. For example, the relation between each potential is as follows:
When GND > PIN A and GND > PIN B, the P-N junction operates as a parasitic diode.
When GND > PIN B, the P-N junction operates as a parasitic transistor.
Parasitic diodes can occur inevitable in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Accordingly, methods by which parasitic diodes
operate, such as applying a voltage that is lower than the GND (P substrate) voltage to an input pin, should not be used.
8. Ground Wiring Pattern
When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns,
placing a single ground point at the ground potential of application so that the pattern wiring resistance and voltage
variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change
the GND wiring pattern of any external components, either.
9. Thermal shutdown circuit
The IC incorporates a built-in thermal shutdown circuit (TSD circuit). The thermal shutdown circuit (TSD circuit) is designed
only to shut the IC off to prevent thermal runaway. It is not designed to protect the IC or guarantee its operation. Do not continue
to use the IC after operating this circuit or use the IC in an environment where the operation of this circuit is assumed.
10. Overcurrent Protection Circuit
An overcurrent protection circuit is incorporated in order to prevention destruction due to short-time overload currents.
Continued use of the protection circuits should be avoided. Please note that the current increases negatively impact the temperature.
11. Damage to the internal circuit or element may occur when the polarity of the Vcc pin is opposite to that of the other pins in
applications. (I.e. Vcc is shorted with the GND pin while an external capacitor is charged.) Use a maximum capacitance
of 1000 μ F for the output pins. Inserting a diode to prevent back-current flow in series with Vcc or bypass diodes
between Vcc and each pin is recommended.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
10/16
TSZ02201-0R6R0A600120-1-2
26.Jun.2012 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| BA15BC0WT | IC REG LDO 1.5V 1A TO220FP |
| BA60BC0WT | IC REG LDO 6V 1A TO220FP-5 |
| ESA35DRMN-S288 | CONN EDGECARD 70POS .125 EXTEND |
| MIC5201-3.0YM TR | IC REG LDO 3V .2A 8-SOIC |
| MIC5219-3.6YMM | IC REG LDO 3.6V .5A 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BA33BC0WT-V5 | 功能描述:低压差稳压器 - LDO LDO REG 3.3V 1A 5PIN RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| BA33C18FP-E2 | 功能描述:IC REG LDO 3.3V/1.8V 1A TO252-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.7V 输入电压:最高 5.5V 电压 - 压降（标准）:0.21V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:剪切带 (CT) 产品目录页面:1100 (CN2011-ZH PDF) 其它名称:576-1852-1 |
| BA33C18HFP-TR | 功能描述:低压差稳压器 - LDO 3,3/1,8V LOW DROP V-REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| BA33C25FP | 制造商:ROHM 制造商全称:Rohm 功能描述:2-output LDO series regulator |
| BA33C25FP-E2 | 功能描述:IC REG LDO 3.3V/2.5V 1A TO-252 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.7V 输入电压:最高 5.5V 电压 - 压降（标准）:0.21V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:剪切带 (CT) 产品目录页面:1100 (CN2011-ZH PDF) 其它名称:576-1852-1 |
发布紧急采购，3分钟左右您将得到回复。