参数资料
| 型号： | BA50BC0WT |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 9/19页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 5V 1A TO220FP-5 |
| 特色产品： | CMOS LDO Regulators |
| 标准包装： | 500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 5V |
| 输入电压： | 最高 16V |
| 电压 - 压降（标准）： | 0.3V @ 200mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1A（最小值） |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 通孔 |
| 封装/外壳： | TO-220-5 整包 |
| 供应商设备封装： | TO-220FP-5 |
| 包装： | 管件 |
| 产品目录页面： | 1368 (CN2011-ZH PDF) |
BAxxBC0 Series BAxxBC0W Series BA00BC0WCP-V5
Datasheet
Refer to the above and implement proper thermal designs so that the IC will not be used under excessive power dissipation
conditions under the entire operating temperature range.
The power consumption Pc of the IC in the event of shorting (i.e. the Vo and GND pins are shorted) can be obtained from
the following equation:
Pc = Vcc × (Icca + Ishort) (Ishort: short current).
● Peripheral Circuit Considerations
? Vcc pin
Insert a capacitor (0.33 μ F approx.) between V CC and GND.
The capacitance will vary depending on the application. Use a suitable capacitance and implement designs with
sufficient margins.
? GND pin
Verify that there is no potential difference between the ground of the application board and the IC.
If there is a potential difference, the set voltage will not be output accurately, resulting in unstable IC operation.
Therefore, lower the impedance by designing the ground pattern as wide and as short as possible.
? CTL terminal
CTL
27k Ω
2k Ω
The CTL terminal turns on at an operating power
supply voltage of 2.0 V or higher and turns off at 0.8 V
31k Ω
or lower.
There is no particular order when turning the power
supply and CTL terminals on or off.
Fig.20 Input Equivalent Circuit
● Vo Terminal
Insert a capacitor between the Vo and GND pins in order to prevent output oscillation.
10.0
2.0
Oscillation region
OUT
1.0
IC
22 μ F
0.5
0.2
Stable region
0.1
0.075
0.05
0
200
Oscillation region
400 600 800
1000 Io [mA]
Fig.21 Output Equivalent Circuit
Fig.22 ESR vs. I O (22 μ F)
The capacitance may vary greatly with temperature changes, thus making it impossible to completely prevent oscillation.
Therefore, use a tantalum aluminum electrolytic capacitor with a low ESR (Equivalent Serial Resistance). The output will
oscillate if the ESR is too high or too low, so refer to the ESR characteristics in Fig.22 and operate the IC within the stable
region. Use a capacitor within a capacitance between 22 μ F and 1,000 μ F.
Below figure, it is ESR-to-Io stability Area characteristics, measured by 22 μ Ｆ -ceramic-capacitor and resistor connected in series.
This characteristic is not equal value perfectly to 22μ Ｆ -aluminum electrolytic capacitor in order to measurement method.
Note, however, that the stable range suggested in the figure depends on the IC and the resistance load involved, and can
vary with the board’s wiring impedance, input impedance, and/or load impedance. Therefore, be certain to ascertain the
final status of these items for actual use.
Keep capacitor capacitance within a range of 22μF to 1000 μ F. It is also recommended that a 0.33 μ F bypass capacitor be
connected as close to the input pin-GND as location possible. However, in situations such as rapid fluctuation of the input
voltage or the load, please check the operation in real application to determine proper capacitance.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
9/16
TSZ02201-0R6R0A600120-1-2
26.Jun.2012 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| BA33BC0WT | IC REG LDO 3.3V 1A TO220FP-5 |
| BA15BC0WT | IC REG LDO 1.5V 1A TO220FP |
| BA60BC0WT | IC REG LDO 6V 1A TO220FP-5 |
| ESA35DRMN-S288 | CONN EDGECARD 70POS .125 EXTEND |
| MIC5201-3.0YM TR | IC REG LDO 3V .2A 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BA50BC0WT-V5 | 功能描述:低压差稳压器 - LDO HOMESECURITY IMAGE PROCESSOR RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| BA50DD0T | 功能描述:低压差稳压器 - LDO 3 5V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| BA50DD0WHFP | 制造商:ROHM 制造商全称:Rohm 功能描述:2A Low Dropout Voltage Regulator with Shut Down Switch |
| BA50DD0WHFP-TR | 功能描述:线性稳压器 - 标准 5 5V RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
| BA50DD0WT | 功能描述:低压差稳压器 - LDO 5 5V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。