- 您现在的位置：买卖IC网 > PDF目录16533 > BA6950FS (Rohm Semiconductor)IC DRIVER REVERSE MOTOR SSOP-A16 PDF资料下载
参数资料
| 型号： | BA6950FS |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 6/13页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER REVERSE MOTOR SSOP-A16 |
| 标准包装： | 2,500 |
| 应用： | 直流电机驱动器 |
| 输出数： | 1 |
| 电流 - 输出： | 400mA |
| 电压 - 负载： | 3 V ~ 16 V |
| 电源电压： | 3 V ~ 6 V |
| 工作温度： | -20°C ~ 75°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-SSOPA |
| 包装： | 管件 |
BA6950FS, BA6951FS
● External application components
Technical Note
1)
2)
3)
4)
5)
6)
7)
8)
9)
Resistor for the current sensing, R5
This is a current sensing resistor, care must be taken to avoid changes in the ground wire pattern in any external
connected component.
Control amplifier gain setting resistor, R1
VCTL pin voltage is buffered to RC pin, and the control gain - V CTLGA - can be set by connecting R1. The current
decided here is output to RT1 pin.
Control amplifier phase compensation capacitor, C1
This phase compensation capacitor for the control amplifier. Please monitor the RT1 pin voltage and confirm no
oscillation. About 33pF is recommended.
Current feedback amplifier gain setting resistor, R4
CS1 pin voltage (the motor current detection) is buffered to CS2 pin - BA6950FS.
ATC pin voltage (the motor current detection) is buffered to CS pin - BA6951FS.
The current feedback gain can be set by R4 connecting to CS2 or CS pin. The current decided here is output to RT2
pin.
Pre-amplifier gain setting resistor, R2, R3
These resistors are to add the control amplifier output and the current feedback amplifier output. This amplifier has
about fourfold gain.
Pre-amplifier phase compensation capacitor, C2
Please connect the capacitor about 0.1μF as the phase compensation of the pre-amplifier, and monitor the driver
output no oscillation.
Stabilization capacitor for the power supply line, C5, C6
Please connect the capacitor of 1 μ F to 100 μ F for the stabilization of the power supply line, and confirm the motor
operation.
Phase compensating capacitor, C3, C4
Noise is generated in output pins or oscillation results in accord with the set mounting state such as power supply
circuit, motor characteristics, PCB pattern artwork, etc. As noise oscillation measures, connect 0.01 μ F to 0.1 μ F
capacitors.
Torque limiter setting, TL pin, BA6951FS only
The motor current is limited so that ATC pin voltage should not exceed TL pin voltage.
● Functional descriptions
Table 3 Logic table
FIN
L
H
L
H
RIN
L
L
H
H
M1
OPEN*
L
H
L
M2
OPEN*
H
L
L
Operation
Stop (idling)
Forward (M2 > M1)
Reverse (M1 > M2)
Brake (stop)
* OPEN is the off state of all output transistors. Please note that this is the state of the connected diodes, which differs from that of the mechanical relay.
www.rohm.com
? 2011 ROHM Co., Ltd. All rights reserved.
6/10
2011.05 - Rev.C
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J4B-EZ-S | CONVERTER MOD DC/DC 95V 25W |
| ILC0402ER6N8K | INDUCTOR CER 6.8NH 0402 |
| ESM11DSEH | CONN EDGECARD 22POS .156 EYELET |
| GEC36DRAS | CONN EDGECARD 72POS R/A .100 SLD |
| ESC22DRXS | CONN EDGECARD 44POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BA6950FS_1 | 制造商:ROHM 制造商全称:Rohm 功能描述:Reversible Motor Driver |
| BA6950FS_10 | 制造商:ROHM 制造商全称:Rohm 功能描述:Reversible Motor Drivers for 0.8A or less (1 Motor) |
| BA6950FS_11 | 制造商:ROHM 制造商全称:Rohm 功能描述:0.5A or Less Reversible Motor Driver (Single Motor) |
| BA6950FS-E2 | 制造商:ROHM Semiconductor 功能描述: |
| BA6951FS | 制造商:ROHM 制造商全称:Rohm 功能描述:0.5A or Less Reversible Motor Driver (Single Motor) |
发布紧急采购，3分钟左右您将得到回复。