- 您现在的位置：买卖IC网 > Datasheet目录206 > BD140D01GR0000 (CH Products)JOYSTICK BD SERIES CONTACTLESS Datasheet资料下载
参数资料
| 型号： | BD140D01GR0000 |
| 厂商： | CH Products |
| 文件页数： | 6/7页 |
| 文件大小： | 0K |
| 描述： | JOYSTICK BD SERIES CONTACTLESS |
| 标准包装： | 1 |
| 系列： | BD |
| 类型： | 操纵杆，面板安装 |
| 输出： | 模拟（霍尔效应） |
| 开关功能： | 1 轴 |
| 触动器类型： | 桨 |
| 端接类型： | 连接器 |
| 其它名称： | 1040-1013 |
BF series
Paddle controllers
CONFIGURATION OPTIONS
OUTPUT OPTIONS
The BF Series Paddle is configured as two “electrical” controls in one mechanical package. The Paddle oper-
ates from 5V and provides two proportional outputs. The second output is accurate to the first within +/-3% of
the power supply. The power supply for the secondary output is also completely independent. Customers may
choose their preference of voltage outputs (gains).
The secondary output can be of the same or inverse polarity to the primary wiper. For example, with a
secondary inverse output, the first and second outputs can be summed and compared to zero to verify that the
joystick is operating correctly. Paddles having two identical outputs of the same polarity may be used to drive
two identical dual redundant circuits.
There are also two Hall effect switches that trigger at pre-determined lever positions.
The BF Series Paddle may be specified with a variety of PWM output options. For more details on available
PWM options please refer to Apem.
ADDITIONAL OUTPUT INFORMATION
SELECTABLE SWITCHING POINTS
The Paddle incorporates two Hall effect switches. The angle of the lever at the switch trigger point can be
selected when ordering.
If no switches are specified then the output on pins 2 and 7 will be unused.
The outputs are configured as ‘open drain’ type with a 1K5 pull up resistor to 5V.
GAIN OPTIONS
The voltage output on the wiper, at full scale deflection is determined by the gain. The gain is expressed as a
percentage of the voltage supplied. Therefore (assuming a 5V supply) a Paddle specified with +/- 25% gain
would yield 1.25V at South, 2.5V at center and 3.75V at North. A range of gain options are available as
standard. All controls are supplied pre-set and no further calibration is needed throughout the lifetime of
operation.
OUTPUT IMPEDANCE
The voltage outputs at center and at each end of travel are specified across an infinite load, with no current
flowing. The output impedance specified in the electrical specification should be taken into account when
designing a system. Load resistance of less than 10K Ohms is not recommended.
HANDLE OPTIONS
The BF Series offers two standard handle options. The taller (74mm) handle provides the most ergonomic
solution while the shorter (50mm) is best suited to hand held applications where a minimized height is
preferred. The taller lever is supplied with the top insert prefitted, however the shorter lever may be specified
with no insert fitted and the snap in inserts supplied loose for ease of customer integration.
Note: The company reserves the right to change specifications without notice.
www.chproducts.com
相关PDF资料 |
PDF描述 |
|---|---|
| BDR-999B | VOLTMETER LRG 2.3" LED BLUE |
| BE-2R-A4 | SWITCH PLUNGER SPDT 25A SCREW |
| BE-R2420-A2 | SWITCH PLUNGER SPDT 25A SCREW |
| BGF 119 E6329 | TVS DIODE ESD 1CH 8V WLP-4-1 |
| BGF 121 E6329 | DIODE TVS ESD WLP-4-1 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD140D03BK0549 | 制造商:APEM 功能描述:JOYSTICK 5 DETENTS +/-5 DEG 制造商:APEM 功能描述:JOYSTICK, 5 DETENTS, +/-5 DEG 制造商:APEM 功能描述:JOYSTICK, 5 DETENTS, +/-5 DEG, Supply Voltage Max:5V, No. of Switch Positions:5, |
| BD140D03BK12275 | 制造商:APEM 功能描述: |
| BD140G | 功能描述:两极晶体管 - BJT 1.5A 80V 12.5W PNP RoHS:否 制造商:STMicroelectronics 配置: 晶体管极性:PNP 集电极—基极电压 VCBO: 集电极—发射极最大电压 VCEO:- 40 V 发射极 - 基极电压 VEBO:- 6 V 集电极—射极饱和电压: 最大直流电集电极电流: 增益带宽产品fT: 直流集电极/Base Gain hfe Min:100 A 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PowerFLAT 2 x 2 |
| BD140G-10-T100-K | 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:PNP SILICON TRANSISTOR |
| BD140G-10-TM3-T | 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:PNP SILICON TRANSISTOR |
发布紧急采购，3分钟左右您将得到回复。