- 您现在的位置：买卖IC网 > Datasheet目录315 > BD1754HFN-TR (Rohm Semiconductor)IC LED DRIVR WHITE BCKLGT 8-HSON Datasheet资料下载
参数资料
| 型号： | BD1754HFN-TR |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 14/19页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR WHITE BCKLGT 8-HSON |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | 线性 |
| 输出数： | 4 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 电源电压： | 2.7 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-HSON |
| 供应商设备封装： | 8-HSON |
| 包装： | 标准包装 |
| 工作温度： | -30°C ~ 85°C |
| 其它名称： | BD1754HFN-DKR BD1754HFN-DKR-ND BD1754HFNDKR |
BD1754HFN
Datasheet
● Operational Notes
(1) Absolute Maximum Ratings
An excess in the absolute maximum ratings, such as applied voltage, temperature range of operating conditions, can
break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any
special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical
safety measures including the use of fuses, etc.
(2) Recommended Operating Conditions
These conditions represent a range within which characteristics can be provided approximately as expected. The
electrical characteristics are guaranteed under the conditions of each parameter. The voltage and temperature
characteristics are also shown under the conditions in respect of electrical ones.
(3) Reverse Connection of Power Supply Connector
The reverse connection of power supply connector can break down ICs. Take protective measures against the breakdown
due to the reverse connection, such as mounting an external diode between the power supply and the IC’s power
supply terminal.
(4) Power Supply Line
Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines.
Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal.
At the same time, in order to use an electrolytic capacitor, thoroughly check to be sure that the characteristics of the
capacitor to be used present no problem including the occurrence of capacity dropout at a low temperature, thus
determining the constant.
(5) GND Voltage
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state.
Furthermore, check to be sure that no terminal is operated at a potential lower than the GND voltage including an
actual electric transient.
(6) Short Circuit between Terminals and Erroneous Mounting
In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting
can break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or
between the terminal and the power supply or the GND terminal, the ICs can break down.
(7) Operation in Strong Electromagnetic Field
Be noted that using ICs in the strong electromagnetic field can cause a malfunction.
(8) Inspection with set PCB
On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress.
Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set
PCB to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to
the jig. After the completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In
addition, for protection against static electricity, establish a ground for the assembly process and pay thorough attention
to the transportation and the storage of the set PCB.
(9) Input Terminals
In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the
parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of
the input terminal. Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input
terminals a voltage lower than that applied to the GND respectively, so that any parasitic element will operate.
Furthermore, do not apply a voltage to the input terminals when no power supply voltage is applied to the IC. In
addition, even if the power supply voltage is applied, apply to the input terminals a voltage lower than the power supply
voltage or within the guaranteed value of electrical characteristics.
(10) Ground Wiring Pattern
If small-signal GND and large-current GND are provided, it will be recommended to separate the large-current GND
pattern from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that
resistance to the wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of
the small-signal GND. Pay attention not to cause fluctuations in the GND wiring pattern of external parts as well.
(11) Thermal Design
Perform thermal design in which there are adequate margins by taking into account the permissible dissipation (Pd) in
actual states of use.
Status of this document
The Japanese version of this document is formal specification. A customer may use this translation version only for a reference
to help reading the formal version.
If there are any differences in translation version of this document formal version takes priority.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
14/16
TSZ02201-0G3G0C200060-1-2
9.NOV.2012 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| BD2802GU-E2 | IC LED DRIVER RGB 24-VCSP |
| BD6062GU-E2 | IC LED DRIVER FALSH VCSP85H2 |
| BD6066EKN-E2 | IC LED DRVR WHITE BCKLT 28-HVQFN |
| BD6069GUT-E2 | IC LED DRIVR WHITE BCKLGT 8-VCSP |
| BD6081GVW-E2 | IC LED DRIVER BACKLIGHT 63SBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD175-6 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:TRANSISTOR | BJT | NPN | 45V V(BR)CEO | 3A I(C) | TO-126 |
| BD1756STU | 功能描述:两极晶体管 - BJT NPN Epitaxial Sil RoHS:否 制造商:STMicroelectronics 配置: 晶体管极性:PNP 集电极—基极电压 VCBO: 集电极—发射极最大电压 VCEO:- 40 V 发射极 - 基极电压 VEBO:- 6 V 集电极—射极饱和电压: 最大直流电集电极电流: 增益带宽产品fT: 直流集电极/Base Gain hfe Min:100 A 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PowerFLAT 2 x 2 |
| BD176 | 制造商:ISC 制造商全称:Inchange Semiconductor Company Limited 功能描述:Silicon PNP Power Transistors |
| BD176-10 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:TRANSISTOR | BJT | PNP | 45V V(BR)CEO | 3A I(C) | TO-126 |
| BD17610STU | 功能描述:两极晶体管 - BJT PNP Epitaxial Sil RoHS:否 制造商:STMicroelectronics 配置: 晶体管极性:PNP 集电极—基极电压 VCBO: 集电极—发射极最大电压 VCEO:- 40 V 发射极 - 基极电压 VEBO:- 6 V 集电极—射极饱和电压: 最大直流电集电极电流: 增益带宽产品fT: 直流集电极/Base Gain hfe Min:100 A 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PowerFLAT 2 x 2 |
发布紧急采购，3分钟左右您将得到回复。