参数资料
| 型号： | BD2051AFJ-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 15/25页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH HIGH SIDE 1CH SOP-J8 |
| 特色产品： | High Side Switch Regulators |
| 标准包装： | 1 |
| 类型： | 高端 |
| 输入类型： | 非反相 |
| 输出数： | 1 |
| 导通状态电阻： | 80 毫欧 |
| 电流 - 输出 / 通道： | 500mA |
| 电流 - 峰值输出： | 1A |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOP-J |
| 包装： | 标准包装 |
| 产品目录页面： | 1371 (CN2011-ZH PDF) |
| 其它名称： | BD2051AFJ-E2DKR |
BD2041AFJ
BD2051AFJ
Datasheet
● Typical Application Circuit
5V(typ.)
VBUS
D+
D-
GND
IN
Regulator
OUT
10k to
GND
OUT
VBUS
USB
Controller
100k ?
C IN
IN
IN
OUT
OUT
+
C L -
D+
D-
EN(/EN) /OC
GND
● Application Information
When excessive current flows owing to output shortcircuit or so, ringing occurs by inductance of power source line to IC,
and may cause bad influences upon IC actions. In order to avoid this case, connect a bypath capacitor by IN terminal and
GND terminal of IC. 1 μ F or higher is recommended.
Pull up /OC output by resistance 10k ? to 100k ? .
Set up value which satisfies the application as C L .
This system connection diagram doesn’t guarantee operating as the application.
The external circuit constant and so on is changed and it uses, in which there are adequate margins by taking into account
external parts or dispersion of IC including not only static characteristics but also transient characteristics.
● Functional Description
1. Switch operation
IN terminal and OUT terminal are connected to the drain and the source of switch MOSFET respectively. And the IN
terminal is used also as power source input to internal control circuit.
When the switch is turned on from EN/EN control input, IN terminal and OUT terminal are connected by a 80m ? switch.
In on status, the switch is bidirectional. Therefore, when the potential of OUT terminal is higher than that of IN terminal,
current flows from OUT terminal to IN terminal.
Since a parasitic diode between the drain and the source of switch MOSFET is canceled, in the off status, it is possible to
prevent current from flowing reversely from OUT to IN.
2. Thermal shutdown circuit (TSD)
If over current would continue, the temperature of the IC would increase drastically. If the junction temperature were
beyond 140°C (typ.) in the condition of over current detection, thermal shutdown circuit operates and makes power switch
turn off and outputs error flag (/OC). Then, when the junction temperature decreases lower than 120°C (typ.), power
switch is turned on and error flag (/OC) is cancelled. Unless the fact of the increasing chips temperature is removed or
the output of power switch is turned off, this operation repeats.
The thermal shutdown circuit operates when the switch is on (EN,/EN signal is active).
www.rohm.com
? 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
15/22
TSZ02201-0E3E0H300290-1-2
08.Mar.2013 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| BD2055AFJ-E2 | IC SWITCH HIGH SIDE 1CH SOP-J8 |
| BD2061AFJ-E2 | IC SWITCH USB HI SIDE 1CH SOP-J8 |
| BD2206G-TR | IC LOAD SWITCH 0.5A SSOP5 |
| BD25KA5WF-E2 | IC REG LDO 2.5V .5A SOP8 |
| BD3506F-E2 | IC REG LDO ADJ 2.5A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD2052AFJ | 制造商:ROHM 制造商全称:Rohm 功能描述:2ch High Side Switch ICs for USB Devices and Memory Cards |
| BD2052AFJ-E2 | 功能描述:开关变换器、稳压器与控制器 2Ch; Lg Current Out USB High Side Switch RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| BD2055AFJ | 制造商:ROHM 制造商全称:Rohm 功能描述:1ch High Side Switch ICs for USB Devices and Memory Cards |
| BD2055AFJ-E2 | 功能描述:开关变换器、稳压器与控制器 1Ch; Sm Current Out USB High Side Switch RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| BD2056AFJ | 制造商:ROHM 制造商全称:Rohm 功能描述:2ch Small Current Output USB High Side Switch ICs |
发布紧急采购，3分钟左右您将得到回复。