- 您现在的位置：买卖IC网 > Datasheet目录315 > BD2802GU-E2 (Rohm Semiconductor)IC LED DRIVER RGB 24-VCSP Datasheet资料下载
参数资料
| 型号： | BD2802GU-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 23/30页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER RGB 24-VCSP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 输出数： | 6 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 通用 |
| 类型 - 次要： | 颜色，RGB |
| 频率： | 800kHz ~ 1.2MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFBGA，24-CSPBGA |
| 供应商设备封装： | VCSP85H2 |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 产品目录页面： | 1371 (CN2011-ZH PDF) |
| 其它名称： | BD2802GU-E2DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页
BD2802GU
Technical Note
● Description of other operations
1. Reset
There are two types of reset: software reset and hardware reset.
(1) Software reset
- Setting the register (SFTRST) to “1” causes all the registers to be initialized.
- The registers subject to software reset automatically return to zero (Auto Return 0).
(2) Hardware reset
- Changing the RESETB terminal setting from “H” to “L” causes a state subject to hardware reset.
- Attempting hardware reset causes the states of all registers and output terminals to be initialized to their initial
values, so that address reception is entirely stopped.
- Attempting reset in the hardware reset state causes the RESETB terminal state to change from “L” to “H” and vice versa.
- The RESETB terminal is provided with a filter circuit and a duration of 5μs or less with the terminal set to “L” is not
recognized as hardware reset.
(3) Reset sequence
- When hardware reset is attempted during software reset, software reset is already cleared when hardware reset is
cleared (because the software reset initial value is 0).
2. Thermal shutdown
The thermal shutdown is effective for LED and OSC portions.
The thermal shutdown function is activated when the detected temperature is approx. 195 ? C.
The detected temperature has a hysteresis and the detection cancel temperature is approx. 175 ? C (reference value in design).
3. I/O portion
While the RESETB terminal is in “L” state, no input signal is propagated to the IC logic portion because SDA and SCL
input buffer operations are all stopped.
When RESETB=L, output is fixed at “H.”
SCL
Level shifter
(SDA)
EN
Logic
RESETB
Special care should be taken because a current path may be formed via a terminal protection diode, depending on an I/O
power-on sequence or an input level.
4. Power on/off sequence
Voltage shall be applied as follows at driver activation. When a delay element is connected to a VIO voltage source
and a reset cancel signal is input to the RESETB terminal, special care should be taken to the rising time of VIO voltage
to delay the RESETB signal without fail.
VBAT
T VBATOFF
VIO
T R STB=m in 0.1m s
T R ST=m in 0.1m s
RESETB
T AC SS=m in 0.1m s
Register 御
レ ジスタ制 control
不 可
Register control disabled
可 能
Register control enabled
不 可
Register control disabled
5. Terminating the unused terminals
Be sure to set the test terminals and unused terminals as summarized in the following table.In addition, refer to the
preceding equivalent circuit and terminate the above terminals in a way that no problem occurs during actual use.
T1, T2, T3, T4 Test input terminals. Short-circuit these terminals to GND.
LED terminals not to be used
Short-circuit these terminals to GND.
In this case, don’t set the registers related to LEDs not to be used.
RGB1CNT, RGB2CNT Short-circuit these terminals to GND.(Built-in pull-down resistance)
CLKIO
ADDSEL
Short-circuit this terminal to GND.(Built-in pull-down resistance)
Be sure to short-circuit this terminal to VBAT or GND.
www.rohm.com
? 2011 ROHM Co., Ltd. All rights reserved.
23/27
2011.04 - Rev.A
相关PDF资料 |
PDF描述 |
|---|---|
| BD6062GU-E2 | IC LED DRIVER FALSH VCSP85H2 |
| BD6066EKN-E2 | IC LED DRVR WHITE BCKLT 28-HVQFN |
| BD6069GUT-E2 | IC LED DRIVR WHITE BCKLGT 8-VCSP |
| BD6081GVW-E2 | IC LED DRIVER BACKLIGHT 63SBGA |
| BD6083GUL-E2 | IC LED DRIVER BKLT 36VCSP50L3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD2808MUV-ME2 | 功能描述:24CH CONSTANT CURRENT LED DRIVER 制造商:rohm semiconductor 系列:* 包装:剪切带（CT） 零件状态:在售 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商器件封装:VQFN48MCV070 标准包装:1 |
| BD2812GU | 制造商:ROHM 制造商全称:Rohm 功能描述:RGB Illumination LED Driver for mobile phone |
| BD284 | 制造商:Klein Tools Inc 功能描述: |
| BD28411MUV-E2 | 功能描述:Amplifier IC 2-Channel (Stereo) Class D 32-VQFN (5x5) 制造商:rohm semiconductor 系列:- 包装:剪切带（CT） 零件状态:Not For New Designs 类型:D 类 输出类型:2 通道（立体声） 不同负载时的最大输出功率 x 通道数:9W x 2 @ 8 欧姆 电压 - 电源:4.5 V ~ 13 V 特性:消除爆音，短路保护 安装类型:表面贴装 工作温度:-25°C ~ 85°C（TA） 供应商器件封装:32-VQFN（5x5） 封装/外壳:32-VFQFN 裸露焊盘 标准包装:1 |
| BD28411MUV-EVK-001 | 功能描述:BD28411 - 2-Channel (Stereo) Output Class D Audio Amplifier Evaluation Board 制造商:rohm semiconductor 系列:- 零件状态:过期 放大器类型:D 类 输出类型:2 通道（立体声） 不同负载时的最大输出功率 x 通道数:9W x 2 @ 8 欧姆 电压 - 电源:4.5 V ~ 13 V 板类型:完全填充 使用的 IC/零件:BD28411 所含物品:板 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。