- 您现在的位置：买卖IC网 > PDF目录16667 > BD6210F-E2 (Rohm Semiconductor)IC H-BRIDGE DVR 7V 1CH .5A 8-SOP PDF资料下载
参数资料
| 型号： | BD6210F-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 11/21页 |
| 文件大小： | 0K |
| 描述： | IC H-BRIDGE DVR 7V 1CH .5A 8-SOP |
| 特色产品： | H-Bridge Driver IC |
| 标准包装： | 1 |
| 应用： | 直流电机驱动器 |
| 输出数： | 1 |
| 电流 - 输出： | 500mA |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-SOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1371 (CN2011-ZH PDF) |
| 其它名称： | BD6210F-E2DKR |
BD621xxx Series
Datasheet
e) f) PWM control mode A
The rotational speed of the motor can be controlled by the duty cycle of the PWM signal fed to the FIN pin or the
RIN pin. In this mode, the high side output is fixed and the low side output is switching, corresponding to the input
signal. The state of the output toggles between "L" and "Hi-Z".
The frequency of the input PWM signal can be between 20kHz and 100kHz. The circuit may not operate properly for
PWM frequencies below 20kHz and above 100kHz. Note that control may not be attained by switching on duty at
frequencies lower than 20kHz, since the operation functions via the stand-by mode. To operate in this mode,
connect the VREF pin to the VCC pin. In addition, establish a current path for the recovery current from the motor,
by connecting a bypass capacitor (10μF or higher is recommended) between VCC and ground.
ON
OFF
M
Control input : H
OFF
ON
ON
OFF
M
Control input : L
OFF
OFF
Fig.31 PWM control mode A operation (output stage)
FIN
RIN
OUT1
OUT2
Fig.32 PWM control mode A operation (timing chart)
g) h) PWM control mode B
The rotational speed of the motor can be controlled by the duty cycle of the PWM signal fed to the FIN pin or the
RIN pin. In this mode, the low side output is fixed and the high side output is switching, corresponding to the input
signal. The state of the output toggles between "L" and "H".
The frequency of the input PWM signal can be between 20kHz and 100kHz. The circuit may not operate properly for
PWM frequencies below 20kHz and above 100kHz. To operate in this mode, connect the VREF pin to the VCC pin.
In addition, establish a current path for the recovery current from the motor, by connecting a bypass capacitor (10μF
or higher is recommended) between VCC and ground.
ON
OFF
M
Control input : H
OFF
ON
ON
OFF
M
Control input : L
OFF
OFF
Fig.33 PWM control mode B operation (output stage)
FIN
RIN
OUT1
OUT2
Fig.34 PWM control mode B operation (timing chart)
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
11/18
TSZ02201-0P2P0B300070-1-2
25.Dec.2012 Rev.002
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B73-EX | CONVERTER MOD DC/DC 24V 75W |
| PM5022-681M-RC | INDUCTOR POWER 680UH 0.7A SMD |
| M1BXK-1036R | IDC CABLE - MSR10K/MC10M/X |
| AH2984-YG-13 | IC FAN CONTROLLER BLDC SOT89-5L |
| M3CCA-2436J | IDC CABLE - MKC24A/MC24G/MKC24A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD6210HFP | 制造商:ROHM 制造商全称:Rohm 功能描述:DC Brush Motor Drivers (7V max.) |
| BD6210HFP-TR | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE 7V max 1 Chan 0.5A 1.0ohm RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| BD6211 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (7V max.) |
| BD62110AEFJ-E2 | 功能描述:36V 1 CH DC BRUSH MOTOR DRIVERS 制造商:rohm semiconductor 系列:- 包装:剪切带（CT） 零件状态:在售 电机类型 - 步进:- 电机类型 - AC，DC:有刷直流 功能:驱动器 - 全集成，控制和功率级 输出配置:半桥（2） 接口:PWM 技术:DMOS 步进分辨率:- 应用:打印机 电流 - 输出:700mA 电压 - 电源:8 V ~ 28 V 电压 - 负载:8 V ~ 28 V 工作温度:-25°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽）裸露焊盘 供应商器件封装:8-HTSOP-J 标准包装:1 |
| BD6211F | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge driver for DC brush motor |
发布紧急采购，3分钟左右您将得到回复。