- 您现在的位置：买卖IC网 > PDF目录16693 > BD6212FP-EVAL-N (Rohm Semiconductor)BOARD EVAL FOR BD6212FP PDF资料下载
参数资料
| 型号： | BD6212FP-EVAL-N |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 11/21页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR BD6212FP |
| 特色产品： | H-Bridge Driver IC |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电机控制 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | BD6212 |
| 主要属性： | 1 个半桥驱动器 |
| 已供物品： | 板 |
| 相关产品： | BD6212HFPDKR-ND - IC H-BRIDGE DVR 7V 1CH 2A HRP7 BD6212HFPCT-ND - IC H-BRIDGE DVR 7V 1CH 2A HRP7 BD6212HFPTR-ND - IC H-BRIDGE DVR 7V 1CH 2A HRP7 BD6212FP-E2DKR-ND - IC H-BRIDGE DRIVER 1CH 2A HSOP25 BD6212FP-E2CT-ND - IC H-BRIDGE DRIVER 1CH 2A HSOP25 BD6212FP-E2TR-ND - IC H-BRIDGE DRIVER 1CH 2A HSOP25 |
| 其它名称： | EVAL-N.BD6212FP EVAL-N.BD6212FP-ND |
BD621xxx Series
Datasheet
e) f) PWM control mode A
The rotational speed of the motor can be controlled by the duty cycle of the PWM signal fed to the FIN pin or the
RIN pin. In this mode, the high side output is fixed and the low side output is switching, corresponding to the input
signal. The state of the output toggles between "L" and "Hi-Z".
The frequency of the input PWM signal can be between 20kHz and 100kHz. The circuit may not operate properly for
PWM frequencies below 20kHz and above 100kHz. Note that control may not be attained by switching on duty at
frequencies lower than 20kHz, since the operation functions via the stand-by mode. To operate in this mode,
connect the VREF pin to the VCC pin. In addition, establish a current path for the recovery current from the motor,
by connecting a bypass capacitor (10μF or higher is recommended) between VCC and ground.
ON
OFF
M
Control input : H
OFF
ON
ON
OFF
M
Control input : L
OFF
OFF
Fig.31 PWM control mode A operation (output stage)
FIN
RIN
OUT1
OUT2
Fig.32 PWM control mode A operation (timing chart)
g) h) PWM control mode B
The rotational speed of the motor can be controlled by the duty cycle of the PWM signal fed to the FIN pin or the
RIN pin. In this mode, the low side output is fixed and the high side output is switching, corresponding to the input
signal. The state of the output toggles between "L" and "H".
The frequency of the input PWM signal can be between 20kHz and 100kHz. The circuit may not operate properly for
PWM frequencies below 20kHz and above 100kHz. To operate in this mode, connect the VREF pin to the VCC pin.
In addition, establish a current path for the recovery current from the motor, by connecting a bypass capacitor (10μF
or higher is recommended) between VCC and ground.
ON
OFF
M
Control input : H
OFF
ON
ON
OFF
M
Control input : L
OFF
OFF
Fig.33 PWM control mode B operation (output stage)
FIN
RIN
OUT1
OUT2
Fig.34 PWM control mode B operation (timing chart)
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
11/18
TSZ02201-0P2P0B300070-1-2
25.Dec.2012 Rev.002
相关PDF资料 |
PDF描述 |
|---|---|
| EBM28DCTD-S288 | CONN EDGECARD 56POS .156 EXTEND |
| GCM15DCCS-S189 | CONN EDGECARD 30POS R/A .156 SLD |
| H3CKH-1006M | IDC CABLE - HKC10H/AE10M/HPK10H |
| AFK337M06E16T-F | CAP ALUM 330UF 6.3V 20% SMD |
| ABM06DRXN | CONN EDGECARD 12POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD6212HFP | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge driver for DC brush motor |
| BD6212HFP-TR | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE 7V max 1 Chan 2.0A 0.5ohm RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| BD6215 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (7V max.) |
| BD6216 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (7V max.) |
| BD6217 | 制造商:ROHM 制造商全称:Rohm 功能描述:H-bridge drivers (7V max.) |
发布紧急采购，3分钟左右您将得到回复。