参数资料
型号: BD8151EFV-E2
厂商: Rohm Semiconductor
文件页数: 11/20页
文件大小: 0K
描述: IC PWR SUPPLY 1CH 20HTSSOP
标准包装: 2,500
应用: LCD 监视器,笔记本电脑显示器
电流 - 电源: 1.2mA
电源电压: 2.5 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 20-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 20-HTSSOP-B
包装: 带卷 (TR)
BD8151EFV, BD8157EFV
Technical Note
(9) Setting R C , C C of the phase compensation circuit
In the current mode control, since the coil current is controlled, a pole (phase lag) made by the CR filter composed of the
output capacitor and load resistor will be created in the low frequency range, and a zero (phase lead) by the output
capacitor and ESR of capacitor will be created in the high frequency range. In this case, to cancel the pole of the power
amplifier, it is easy to compensate by adding the zero point with C C and R C to the output from the error amplifier as shown
in the illustration.
Open loop gain
A
fp(Min)
fp =
1
2 ? ? Ro ? Co
[Hz]
Gain
0
fp(Max)
fz (ESR) =
1
2 ? ? E SR ? Co
[Hz]
【 dB 】
l OUT Min
0
l OUT Max
fz(ESR)
Pole at the power amplification stage
When the output current reduces, the load resistance
R O increases and the pole frequency lowers.
Phase
【 deg 】
-90
fp(Min) =
1
2 ? ? Ro Max ? Co
[Hz]
(At light-load)
Error amplifier phase compensation
fz(Max) =
1
2 ? ? Ro Min ? Co
[Hz]
(At heavy-load)
Gain
【 dB 】
A
0
Zero at the power amplification stage
When the output capacitor is set larger, the pole
frequency lowers but the zero frequency will not
change. (This is because the capacitor ESR
becomes 1/2 when the capacitor becomes 2 times.)
0
Phase
【 deg 】 -90
fp (Amp.) =
1
2 ? ? Rc ? Cc
[Hz]
Fig. 34 Gain vs Phase
L
Vo
V CC
Cin
COMP
Vcc,PVcc
SW
ESR
Co
Ro
Rc
GND,PGND
Cc
Fig. 35 Application Circuit Diagram
It is possible to realize the stable feedback loop by canceling the pole fp (Min.), which is created by the output capacitor
and load resistor, with CR zero compensation of the error amplifier as shown below.
fz (Amp.) = fp (Min.)
1
1
2 ? ? Rc ? Cc
=
2 ? ? Romax ? Co
[Hz]
As the setting range for the resistor, 1 k ? to 10 k ? is recommended. When the resistor is set to 1 k ? or lower, the effect by
phase compensation becomes low and it may cause the oscillation of output voltage. When it is set to 10 k ? or larger, the
COMP pin becomes Hi-Z and the switching noise becomes easy to superpose. Therefore the stable switching pulse
cannot be generated and the irregular ripple voltage may be generated on the output voltage.
As the setting range for the capacitance, 3,300 pF to 10,000 pF is recommended. When the capacitance is set to 3,300 pF
or lower, the irregular ripple voltage may be generated on the output voltage due to the effect of switching noise. When it is
set to 10,000 pF or larger, the response becomes worse and the output voltage fluctuation becomes large. Accordingly it
may require the output capacitor which is larger than the necessary value.
www.rohm.com
? 2009 ROHM Co., Ltd. All rights reserved.
11/17
2009.07 - Rev.B
相关PDF资料
PDF描述
GEM30DTMI-S189 CONN EDGECARD 60POS R/A .156 SLD
SN65LVDM31-32BEVM EVAL MOD FOR SN65LVDM31/LVDS32B
EEM44DSEP-S243 CONN EDGECARD 88POS .156 EYELET
BD6222HFP-TR IC H-BRIDGE DVR 18V 1CH 2A HRP7
VE-B51-EX CONVERTER MOD DC/DC 12V 75W
相关代理商/技术参数
参数描述
BD8152FVM 制造商:ROHM 制造商全称:Rohm 功能描述:High-efficiency Step-up Switching Regulators with Built-in Power MOSFET
BD8152FVM_1 制造商:ROHM 制造商全称:Rohm 功能描述:High-efficiency Step-up Switching Regulators with Built-in Power MOSFET
BD8152FVM_11 制造商:ROHM 制造商全称:Rohm 功能描述:High-efficiency Step-up Switching Regulators with Built-in Power MOSFET
BD8152FVM-E2 制造商:ROHM 制造商全称:Rohm 功能描述:High-efficiency Step-up Switching Regulators with Built-in Power MOSFET
BD8152FVM-TR 功能描述:LCD 驱动器 REGULATOR RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube