参数资料
| 型号： | BG2A-NFH |
| 厂商： | Powerex Inc |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | KIT DEV BOARD FOR IGBT |
| 标准包装： | 1 |
| 主要目的： | 电源管理，IGBT 电源模块驱动器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | Powerex IGBT 模块 |
| 已供物品： | 3 个板 |
| 相关产品： | CM600DU-24NFH-ND - IGBT MOD DUAL 1200V 600A NFH SER CM400DU-24NFH-ND - IGBT MOD DUAL 1200V 400A NFH SER 835-1091-ND - IGBT MOD DUAL 600V 400A NFH SER 835-1087-ND - IGBT MOD DUAL 1200V 300A NFH SER CM300DU-12NFH-ND - IGBT MOD DUAL 600V 300A NFH SER CM200DU-24NFH-ND - IGBT MOD DUAL 1200V 200A NFH SER 835-1082-ND - IGBT MOD DUAL 600V 200A NFH SER CM150DU-24NFH-ND - IGBT MOD DUAL 1200V 150A NFH SER 835-1064-ND - IC IGBT GATE DVR/DC-DC CONV 12A 835-1004-ND - IGBT MOD DUAL 1200V 100A NFH SER |
Figure 3: BG2A External Wiring Diagram
G
E
1
G1
C1
RC Filter to remove
noise on fault signal
CN1
E1
To logic
RC~10μs
GND
+V S
FO
C
CN2
level
control
circuits
CMOS type buffer
must sink 15mA
1
IN1
IN2
+V L
G
E
1
G2
E2
C2E1
C
CN3
E2
IGBT Module
VLA500 series driver. A CMOS buffer that actively pulls its output high is recommended for maintaining good
common mode noise immunity in the off state. Open collector type drive is not recommended.
The fault signal line on pin 4 of CN1 is active low which means that a fault condition will be indicated by
a low level signal. During normal operation pin 4 is pulled high to the +5V supply (+V L ) by the 4.7K resistor R3.
If either of the VLA500 series gate drivers detects a short circuit condition the fault isolation optos (OP1, OP2)
turn on and pull pin 4 of CN1 low. When a fault is detected the hybrid gate drivers disable the output and
produce a fault signal for a minimum of 1ms. Any signal on the fault line that is significantly shorter than 1ms
can not be a legitimate fault so it should be ignored. Therefore, for a robust noise immune design, it is
recommended that an RC filter with a time constant of approximately 10μs be added between pin 4 and the
controller as shown in figure 3.
Printed Circuit Layout: Figure 4 shows the layout of the BG2A two channel gate driver board. The
compact 2” x 4” circuit board with only 24 components clearly demonstrates the advantage of using the VLA500
Figure 4: BG2A Printed Circuit Board Layout
Component Side Copper
Component Legend
4
Solder Side Copper
相关PDF资料 |
PDF描述 |
|---|---|
| BG2B-5015 | KIT DEV BOARD 2CN 5A FOR IGBT |
| BG2C-5015 | KIT DEV BOARD 5A FOR IGBT |
| BH-0111 | FUSEBLOCK 1 HOLE #1 STUD SIZE |
| BJ150 | TRS BLKHD PUSH-ON JACK STR SLD |
| BJ157F-2C | TRS BULKHD JACK STR FLNG SLD POT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BG2B | 制造商:Powerex Power Semiconductors 功能描述:GATE DRIVER 制造商:Powerex, Inc. 功能描述:BG2B Board Is A Bare PCB Only |
| BG2B020 | 制造商:Siemens 功能描述: |
| BG2B-1515 | 功能描述:KIT DEV BOARD 1.5A FOR IGBT RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| BG2B-3015 | 功能描述:KIT DEV BOARD 2CN 3A FOR IGBT RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| BG2B-5015 | 功能描述:KIT DEV BOARD 2CN 5A FOR IGBT RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
发布紧急采购，3分钟左右您将得到回复。