参数资料
| 型号： | BGF.0M.100.XAV |
| 厂商： | LEMO |
| 文件页数： | 37/40页 |
| 文件大小： | 0K |
| 描述： | CAP FOR PLUG (CDF) |
| 产品培训模块： | M Series |
| 特色产品： | M Series Connectors |
| 标准包装： | 10 |
| 系列： | BGF |
| 附件类型： | 盖帽（护盖），堵头 |
| 适用于相关产品： | 0M 系列插头 |
| 材质： | 铝，镀镍 |
| 特点： | 包含带 |
| 颜色： | 银 |
| 配用： | 1124-1188-ND - CONN PLUG 5POS STRGHT PIN CRIMP 1124-1187-ND - CONN PLUG 3POS STRGHT PIN CRIMP 1124-1185-ND - CONN PLUG 5POS STRGHT SKT CRIMP 1124-1182-ND - CONN PLUG 5POS STRGHT PIN CRIMP |
| 其它名称： | 1124-1173 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页
Assembly instructions for plugs and sockets (with optional mold stop)
1
FG ●
?
?
PH ●
PB ●
1
L ± 0.5
T ± 0.2
1.
Cable preparation
Strip the cable according to dimen-
sions of the table, then widen the shield.
Series
0M to 5M
L
20
S
15
T
3.5
Note : dimensions are in mm.
S ± 0.5
2.1 With shielded cables, widen and pull the shield all the way to the back.
1
1
Crimp
Crimp
Steel tie-wrap band (~3 mm wide)
2. Cable termination
Fix the appropriate positioner onto the crimping tool and set the selec-
tor to the number corresponding to the AWG of the conductor used as
indicated on the positioner label.
Fit the conductor into the contact ? ; make sure it is visible through the
contact’s inspection hole.
Slide the conductor-contact assembly into the open crimping tool; make
sure that the contact is pushed fully into the positioner. Close the tool.
Remove from crimping tool and check that conductor is secure in
contact and shows in inspection hole.
into the the cable seal.
2.2 Arrange rear conductor-contact assemblies according to the markings,
Push them deeply into the insulator, using tweezers if necessary;
check that all the contacts are correctly located in the insulator: 1)
by verifying the alignment of the contacts at the front of the insulator
and 2) by gently pulling on each conductor.
Verification should also be made using the appropriate retention tes-
ting tool.
Bring it with a band-it the of furnished) to mold in
2.3 Secure the shield around tie-wrap (not connector until fix the shield stop. place.
Cut off the possible shield surplus.
Steel tie-wrap band (~3 mm wide)
www.lemo.com
Overmolding
Overmolding
2.4 Custom overmold cable assembly.
35
相关PDF资料 |
PDF描述 |
|---|---|
| N74F51D,602 | IC GATE AND/OR/INVERT 2IN 14SOIC |
| 74AUP1G58GW,125 | IC CONFIG MULTI-FUNC GATE SC-88 |
| MC100EP05DTG | IC GATE AND/NAND ECL 2INP 8TSSOP |
| GMA.2B.060.DB | STRAIN RELIEF 6.0MM DIA WHITE |
| OSTET220252 | CONN PLUG HEADER 22PS 7.62MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BGF100E6327XT | 制造商:Infineon Technologies AG 功能描述:MICROPHONE FILTER WITH LOW PASS CHARACTERISTIC OFFERING A VERY HIGH STOP BAND ATTENUATION UP TO 6 GHZ |
| BGF104C | 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:HSMMC Inter face Fi l ter and ESD Protect ion |
| BGF104CE6328XTSA1 | 制造商:Infineon Technologies AG 功能描述:HIPAC WLP - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC HSMMC FILTER/ESD PROT WLP-16 |
| BGF104E6327XT | 制造商:Infineon Technologies AG 功能描述:HSMMC Interface Filter and ESD Protection 16-Pin WLP T/R |
| BGF106C | 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:SIM Card Interface Filter and ESD Protection |
发布紧急采购，3分钟左右您将得到回复。