- 您现在的位置：买卖IC网 > PDF目录17916 > BK0603HM241-T (Taiyo Yuden)FERRITE BEAD 240 OHM 0201 PDF资料下载
参数资料
| 型号： | BK0603HM241-T |
| 厂商： | Taiyo Yuden |
| 文件页数： | 34/36页 |
| 文件大小： | 0K |
| 描述： | FERRITE BEAD 240 OHM 0201 |
| 产品培训模块： | EMC Applications |
| 产品目录绘图： | (BK,BKP)0603 Series |
| 标准包装： | 1 |
| 系列： | BK |
| 频率对应阻抗： | 240 欧姆 @ 100MHz |
| 额定电流： | 200mA |
| DC 电阻(DCR)： | 最大 800 毫欧 |
| 滤波器类型： | 差模 - 单线 |
| 封装/外壳： | 0201（0603 公制） |
| 安装类型： | 表面贴装 |
| 包装： | 标准包装 |
| 高度（最大）： | 0.013"（0.33mm） |
| 尺寸/尺寸： | 0.024" L x 0.012" W（0.60mm x 0.30mm） |
| 产品目录页面： | 1854 (CN2011-ZH PDF) |
| 其它名称： | 587-1822-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页
3. Considerations for automatic placement
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the inductors when mounting onto the PC boards.
2. The maintenance and inspection of the mounter should be conducted periodically.
Precautions
◆Selection of Adhesives
1. Mounting inductors with adhesives in preliminary assembly, before the soldering stage, may lead to degraded inductor characteristics
unless the following factors are appropriately checked; the size of land patterns, type of adhesive, amount applied, hardening
temperature and hardening period. Therefore, it is imperative to consult the manufacturer of the adhesives on proper usage and
amounts of adhesive to use.
◆Adjustment of mounting machine
1. If the lower limit of the pick-up nozzle is low, too much force may be imposed on the inductors, causing damage. To avoid this, the
following points should be considered before lowering the pick-up nozzle:
（1） The lower limit of the pick-up nozzle should be adjusted to the surface level of the PC board after correcting for deflection of the
board.
（2） The pick-up pressure should be adjusted between 1 and 3N static loads.
（3） To reduce the amount of deflection of the board caused by impact of the pick-up nozzle, supporting pins or back-up pins should be
used under the PC board. The following diagrams show some typical examples of good pick-up nozzle placement:
Item
Single-sided mounting
Improper method
chipping
or cracking
Proper method
supporting pins
or back-up pins
Double-sided mounting
chipping
or cracking
supporting pins
or back-up pins
Technical
considerations
2. As the alignment pin wears out, adjustment of the nozzle height can cause chipping or cracking of the inductors because of mechanical
impact on the inductors. To avoid this, the monitoring of the width between the alignment pin in the stopped position, and maintenance,
inspection and replacement of the pin should be conducted periodically.
◆Selection of Adhesives
1. Some adhesives may cause reduced insulation resistance. The difference between the shrinkage percentage of the adhesive and that of
the inductors may result in stresses on the inductors and lead to cracking. Moreover, too little or too much adhesive applied to the
board may adversely affect component placement, so the following precautions should be noted in the application of adhesives.
（1） Required adhesive characteristics
a. The adhesive should be strong enough to hold parts on the board during the mounting & solder process.
b. The adhesive should have sufficient strength at high temperatures.
c. The adhesive should have good coating and thickness consistency.
d. The adhesive should be used during its prescribed shelf life.
e. The adhesive should harden rapidly.
f. The adhesive must not be contaminated.
g. The adhesive should have excellent insulation characteristics.
h. The adhesive should not be toxic and have no emission of toxic gasses.
（2） When using adhesives to mount inductors on a PCB, inappropriate amounts of adhesive on the board may adversely affect
component placement. Too little adhesive may cause the inductors to fall off the board during the solder process. Too much
adhesive may cause defective soldering due excessive flow of adhesive on to the land or solder pad.
［Recommended conditions］
Amount of adhesives
After inductors are bonded
Figure
0805 case sizes as examples
a a
a 0.3mm min
b 100～120μm
c Area with no adhesive
b
c
c
4. Soldering
◆Selection of Flux
1. Since flux may have a significant effect on the performance of inductors, it is necessary to verify the following conditions prior to use;
（1） Flux used should be with less than or equal to 0.1 wt% （Chlorine conversion method） of halogenated content. Flux having a strong
acidity content should not be applied.
Precautions
（2） When soldering inductors on the board, the amount of flux applied should be controlled at the optimum level.
（3） When using water-soluble flux, special care should be taken to properly clean the boards.
◆Soldering
1. Temperature, time, amount of solder, etc. are specified in accordance with the following recommended conditions, and please contact us
about peak temperature when you use lead-free paste.
? This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E02R01
相关PDF资料 |
PDF描述 |
|---|---|
| QAK2E685KTP | CAP FILM 6.8UF 250VDC AXIAL |
| 940C8P22K | CAP FILM 0.22UF 850VDC AXIAL |
| 930C4P47K-F | CAP FILM 0.47UF 400VDC AXIAL |
| ASML-40.000MHZ-T | OSCILLATOR 40.0000 MHZ 3.3V SMD |
| MMWA6P1K-F | CAP FILM 0.1UF 630VDC AXIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BK-0603HM241TK | 功能描述:电磁干扰滤波珠子、扼流圈和阵列 240ohms 200mA RoHS:否 制造商:AVX 阻抗: 最大直流电流:35 mA 最大直流电阻: 容差: 端接类型:SMD/SMT 电压额定值:25 V 工作温度范围:- 25 C to + 85 C 封装 / 箱体:0603 (1608 metric) |
| BK0603HM471 | 制造商:TAIYO-YUDEN 制造商全称:Taiyo Yuden (U.S.A.), Inc 功能描述:MULTILAYER CHIP BEAD INDUCTORS (BK SERIES) |
| BK0603HM471-T | 功能描述:电磁干扰滤波珠子、扼流圈和阵列 FER BD MLCC 0201 470OHMS 25%, RoHS:否 制造商:AVX 阻抗: 最大直流电流:35 mA 最大直流电阻: 容差: 端接类型:SMD/SMT 电压额定值:25 V 工作温度范围:- 25 C to + 85 C 封装 / 箱体:0603 (1608 metric) |
| BK0603HM600 | 制造商:TAIYO-YUDEN 制造商全称:Taiyo Yuden (U.S.A.), Inc 功能描述:MULTILAYER CHIP BEAD INDUCTORS (BK SERIES) |
| BK0603HM600-T | 功能描述:电磁干扰滤波珠子、扼流圈和阵列 FER BD MLCC 0201 60OHMS 25%, RoHS:否 制造商:AVX 阻抗: 最大直流电流:35 mA 最大直流电阻: 容差: 端接类型:SMD/SMT 电压额定值:25 V 工作温度范围:- 25 C to + 85 C 封装 / 箱体:0603 (1608 metric) |
发布紧急采购，3分钟左右您将得到回复。