- 您现在的位置：买卖IC网 > PDF目录166448 > BQ27500DRZT-V120G4 (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO12 PDF资料下载
参数资料
| 型号： | BQ27500DRZT-V120G4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO12 |
| 封装： | 2.50 X 4 MM, PLASTIC, SON-12 |
| 文件页数： | 15/42页 |
| 文件大小： | 898K |
| 代理商： | BQ27500DRZT-V120G4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
5.2.6
Chg Current Threshold
5.2.7
Quit Current, DSG Relax Time, CHG Relax Time, and Quit Relax Time
5.2.8
Qmax 0 and Qmax 1
5.2.9
Update Status 0 and Update Status 1
5.2.10 Avg I Last Run
5.2.11 Avg P Last Run
bq27500
bq27501
System-Side Impedance Track Fuel Gauge
SLUS785D – SEPTEMBER 2007 – REVISED APRIL 2008
www.ti.com
This register is used as a threshold by many functions in the bq27500/1 to determine if actual charge
current is flowing into or out of the cell. The default for this register is 50 mA, which should be sufficient for
most applications. This threshold should be set low enough to be below any normal charge current but
high enough to prevent noise or drift from affecting the measurement.
The Quit Current is used as part of the Impedance Track algorithm to determine when the bq27500/1
enters relaxation mode from a current-flowing mode in either the charge direction or the discharge
direction. The value of Quit Current is set to a default value of 10 mA and should be above the standby
current of the system.
Either of the following criteria must be met to enter relaxation mode:
| AverageCurrent( ) | < | Quit Current | for Dsg Relax Time
| AverageCurrent( ) | < | Quit Current | for Chg Relax Time
After about 30 minutes in relaxation mode, the bq27500/1 attempts to take accurate OCV readings. An
additional requirement of dV/dt < 4
V/s is required for the bq27500/1 to perform Qmax updates. These
updates are used in the Impedance Track algorithms. It is critical that the battery voltage be relaxed
during OCV readings to and that the current is not be higher than C/20 when attempting to go into
relaxation mode.
Quit Relax Time specifies the minimum time required for AverageCurrent( ) to remain above the
QuitCurrent threshold before exiting relaxation mode.
Generically called Qmax, these dynamic variables contain the respective maximum chemical capacity of
the active cell profiles, and are determined by comparing states of charge before and after applying the
load with the amount of charge passed. They also correspond to capacity at a very low rate of discharge,
such as the C/20 rate. For high accuracy, this value is periodically updated by the bq27500/1 during
operation. Based on the battery cell capacity information, the initial value of chemical capacity should be
entered in the Qmax n field for each default cell profile. The Impedance Track algorithm updates these
values and maintains them the associated actual cell profiles.
Bit 0 (0x01) of the Update Status n registers indicates that the bq27500/1 has learned new Qmax
parameters and is accurate. The remaining bits are reserved. Bits 0 is user-configurable; however, it is
also a status flag that can be set by the bq27500/1. Bit 0 should not be modified except when creating a
golden image file as explained in the application note Preparing Optimized Default Flash Constants for
specific Battery Types (SLUA334). Bit 0 is updated as needed by the bq27500/1.
The bq27500 logs the current averaged from the beginning to the end of each discharge cycle. It stores
this average current from the previous discharge cycle in this register. This register should not be
modified. It is only updated by the bq27500/1 when required.
The bq27500/1 logs the power averaged from the beginning to the end of each discharge cycle. It stores
this average power from the previous discharge cycle in this register. To get a correct average power
reading the bq27500/1 continuously multiplies instantaneous current times Voltage( ) to get power. It then
logs this data to derive the average power. This register should not be modified. It is only updated by the
bq27500/1 when required.
FUNCTIONAL DESCRIPTION
22
相关PDF资料 |
PDF描述 |
|---|---|
| BQ3285LP | 1 TIMER(S), REAL TIME CLOCK, PDIP24 |
| BQ3285LSSN | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
| BQ3285LP | 1 TIMER(S), REAL TIME CLOCK, PDIP24 |
| BQ3285LQ | 1 TIMER(S), REAL TIME CLOCK, PQCC28 |
| BQ3285LSS | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BQ27500DRZT-V130 | 功能描述:电池管理 System-Side Imped RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| BQ27500EVM | 功能描述:电源管理IC开发工具 BQ27500 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| BQ27500-V120 | 制造商:TI 制造商全称:Texas Instruments 功能描述:System-Side Impedance Track? Fuel Gauge |
| BQ27500-V130 | 制造商:TI 制造商全称:Texas Instruments 功能描述:System-Side Impedance Track Fuel Gauge |
| BQ27500YZGR-V130 | 功能描述:电池管理 Sys-Side Impedance Track Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。