参数资料
型号: BQ50120QTA20NRS-G
厂商: SYNQOR INC
元件分类: 电源模块
英文描述: 1-OUTPUT 240 W DC-DC REG PWR SUPPLY MODULE
封装: ROHS COMPLIANT, QUARTER BRICK PACKAGE-5
文件页数: 2/12页
文件大小: 5072K
代理商: BQ50120QTA20NRS-G
Product # BQ50120QTA20
Phone 1-888-567-9596
Doc.# 005-2BQ512J Rev. F
03/26/10
Page 10
Input:
Output:
Current:
PPackage:
ackage:
42-53 V
12 V
20 A
Quarter-brick
T
Technical S
echnical Specification
pecification
Keep Out Areas:
Component Keep Out Area: Keep out areas for components not
referenced to the Primary circuit are shown in shaded areas in
Figure F. The keep out areas shown are consistent with UL's
requirements for Basic Insulation of 0.04" (40 mils) for Pollution
degree 2. User should consult UL standards for other insulation
classes and operating environments.
For applications that require mounting parts BELOW the BusQor
module, one should be aware of potential high levels of electro-
magnetic interference, in addition to safety keep out. Users are
advised to consult SynQor Applications engineering in such
applications.
Copper Keep Out Area: Keep out areas shown in Figure F are
to be observed for Top layer copper traces and vias. Internal lay-
ers buried one or more layers may be exempt, depending on the
PCB material grade and thickness. Users are advised to consult
UL standards for details.
All layers including top and bottom, are subject to the keep out
areas shown around Primary pins of BusQor module. Actual
keep outs along the surface (Creepage) may vary depending on
the PCB material CTI. Users are advised to consult UL standards
for details.
Bridging Components:
Bridging components like EMI filter
capacitors required to be placed as close as possible to the
BusQor module for optimum performance must observe the clear-
ance/creepage requirements of 0.04"(40 mils) between pads to
maintain compliance to UL standards for the overall power sys-
tem.
Note: Referenced keep out widths are adequate to withstand
UL's Basic Insulation Dielectric strength tests for approved PCB
materials. Applications requiring Double or Reinforced insulation
must double the keep out widths shown in Figure F. Keep out
areas shown have standard margins above UL's minimum
requirements.
Output Load Current Calculation:
The BusQor series
allows the converter output load to be measured without adding
a current loop or external shunt resistor to the designer’s PCB
board under test. On the top side of the BusQor converter is a
current sense resistor as shown in Figure G. The output load cur-
rent is proportional to the voltage drop across this sense resistor.
This calculation is detailed below.
A current sense resistor referenced to the primary input is used in
the equation below to calculate the output load current.
Iload = (VRsense(load) - VRsense(no load) ) x 800
where:
Iload = output load current
VRsense(load) = voltage across the sense resistor with
converter under load
VRsense(no load) = voltage across the sense resistor with
converter at zero load
Figure E: Power Up/Down Diagram (not to scale) showing
Start-Up Inhibit Period.
Vin
Vout
12V
On/Off
(N logic)
UVLO
OFF
2ms
16ms
16.1ms
ON
t0
t1
t2
t3
t
Time
Figure F: Keep Out Areas for BusQor module
0.023”
0.01”
1.50”
Primary
Secondary
Bridging
Capacitor
相关PDF资料
PDF描述
BRF34A NPN SILICON TRANSISTOR FOR LOW NOISE RF BROADBAND AMPLIFIER
BRTFHPE05BKSX 5 CONTACT(S), FEMALE, COMBINATION LINE CONNECTOR
BRTFHPE05GYSX 5 CONTACT(S), FEMALE, COMBINATION LINE CONNECTOR
BRTFHPE05WHDX 5 CONTACT(S), FEMALE, COMBINATION LINE CONNECTOR
BS-A281RD-B 7 SEG NUMERIC DISPLAY, RED, 7 mm
相关代理商/技术参数
参数描述
BQ50120QTA20NYC 制造商:SYNQOR 制造商全称:SYNQOR 功能描述:Quarter-brick DC Bus Converter
BQ50120QTA20NYS 制造商:SYNQOR 制造商全称:SYNQOR 功能描述:Quarter-brick DC Bus Converter
BQ50120QTA20PKC 制造商:SYNQOR 制造商全称:SYNQOR 功能描述:Quarter-brick DC Bus Converter
BQ50120QTA20PKS 制造商:SYNQOR 制造商全称:SYNQOR 功能描述:Quarter-brick DC Bus Converter
BQ50120QTA20PNC 制造商:SYNQOR 制造商全称:SYNQOR 功能描述:Quarter-brick DC Bus Converter