- 您现在的位置：买卖IC网 > PDF目录16861 > BQ51013ARHLR (Texas Instruments)IC WIRELESS PWR RCVR 20QFN PDF资料下载
参数资料
| 型号： | BQ51013ARHLR |
| 厂商： | Texas Instruments |
| 文件页数： | 28/45页 |
| 文件大小： | 0K |
| 描述： | IC WIRELESS PWR RCVR 20QFN |
| 标准包装： | 1 |
| 应用： | 无线电源接收器 |
| 电流 - 电源： | 1.5A |
| 电源电压： | 4 V ~ 10 V |
| 工作温度： | 0°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN-EP（4.50x3.50） |
| 包装： | 标准包装 |
| 其它名称： | 296-30568-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
bq51014 is Not Recommended For New Designs
SLUSAY6B – MARCH 2012 – REVISED OCTOBER 2013
Adaptive Communication Limit
The Qi communication channel is established via backscatter modulation as described in the previous sections.
This type of modulation takes advantage of the loosely coupled inductor relationship between the Rx and Tx coil.
Essentially the switching in-and-out of the communication capacitor or resistor adds a transient load to the Rx
coil in order to modulate the Tx coil voltage/current waveform (amplitude modulation). The consequence of this
technique is that a load transient (load current noise) from the mobile device has the same signature. In order to
provide noise immunity to the communication channel, the output load transients must be isolated from the Rx
coil. The proprietary feature Adaptive Communication Limit achieves this by dynamically adjusting the current
limit of the regulator. When the regulator is put in current limit, any load transients will be offloaded to the battery
in the system.
Note that this requires the battery charger IC to have input voltage regulation (weak adapter mode). The output
of the Rx appears as a weak supply if a transient occurs above the current limit of the regulator.
The Adaptive Communication Limit feature has two current limit modes and is detailed in the table below:
Table 5.
I OUT
< 300 mA
> 300 mA
Communication Current Limit
Fixed 400 mA
I OUT + 50 mA
The first mode is illustrated in Figure 25 . In this plot, an output load pulse of 300 mA is periodically introduced on
a DC current level of 200 mA. Therefore, the 400 mA current limit is enabled. The pulses on V RECT indicate that a
communication packet event is occurring. When the output load pulse occurs, the regulator limits the pulse to a
constant 400 mA and; therefore, preserves communication. Note that V OUT drops to 4.5 V instead of GND. A
charger IC with an input voltage regulation set to 4.5 V allows this to occur by offloading the load transient
support to the mobile device’s battery
The second mode is illustrated in Figure 26 . In this plot, an output pulse of 200 mA is periodically introduced on a
DC current level of 400 mA. Therefore, the tracking current mode (I OUT + 50 mA) is enabled. In this mode the
bq5101x measures the active output current and sets the regulators current limit 50 mA above this
measurement. When the load pulse occurs during a communication packet event, the output current is regulated
to 450 mA. As the communication packet event has finished the output load is allowed to increase. Note that
during the time the regulator is in current limit V OUT is reduced to 4.5 V and 5 V when not in current limit.
Synchronous Rectification
The bq5101x provides an integrated, self-driven synchronous rectifier that enables high-efficiency AC to DC
power conversion. The rectifier consists of an all NMOS H-Bridge driver where the backgates of the diodes are
configured to be the rectifier when the synchronous rectifier is disabled. During the initial startup of the WPC
system the synchronous rectifier is not enabled. At this operating point, the DC rectifier voltage is provided by the
diode rectifier. Once V RECT is greater than UVLO, half synchronous mode will be enabled until the load current
surpasses 120 mA. Above 120 mA the full synchronous rectifier stays enabled until the load current drops back
below 100 mA where half synchronous mode is enabled instead.
Temperature Sense Resistor Network (TS)
bq5101x includes a ratiometric external temperature sense function. The temperature sense function has two
ratiometric thresholds which represent a hot and cold condition. An external temperature sensor is recommended
in order to provide safe operating conditions for the receiver product. This pin is best used for monitoring the
surface that can be exposed to the end user (e.g. place the NTC resistor closest to the user).
28
Product Folder Links: bq51013A bq51014
Copyright ? 2012–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| GBM25DREN | CONN EDGECARD 50POS .156 EYELET |
| EEM44DRKS | CONN EDGECARD 88POS DIP .156 SLD |
| GEM25DREI | CONN EDGECARD 50POS .156 EYELET |
| GBM25DREH | CONN EDGECARD 50POS .156 EYELET |
| HTPT66R-683K | IND TOROID PWR HI TEMP 68UH T/H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BQ51013ARHLT | 功能描述:其他电源管理 Qi Int Wireless Pwr Receiver Solution RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| BQ51013AYFPR | 功能描述:电池管理 Qi Int Wireless Pwr Receiver Solution RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| BQ51013AYFPT | 功能描述:电池管理 Qi Int Wireless Pwr Receiver Solution RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| BQ51013B | 制造商:TI 制造商全称:Texas Instruments 功能描述:Highly Integrated Wireless Receiver Qi (WPC V1.1) Compliant Power Supply |
| BQ51013BEVM-764 | 制造商:Texas Instruments 功能描述: 制造商:Texas Instruments 功能描述:CPU |
发布紧急采购，3分钟左右您将得到回复。