参数资料
| 型号： | BR24L01AFV-WE2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 15/41页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 1KBIT 400KHZ 8SSOP |
| 标准包装： | 1 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 1K (128 x 8) |
| 速度： | 400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-LSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-SSOPB |
| 包装： | 标准包装 |
| 产品目录页面： | 1378 (CN2011-ZH PDF) |
| 其它名称： | BR24L01AFV-WE2DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
BR24L □□ -W Series,BR24S □□□ -W Series
Technical Note
● WP valid timing (write cancel)
WP is usually fixed to 'H' or 'L', but when WP is used to cancel write cycle and so forth, pay attention to the following WP
valid timing. During write cycle execution, in cancel valid area, by setting WP='H', write cycle can be cancelled. In both byte
write cycle and page write cycle, the area from the first start condition of command to the rise of clock to taken in D0 of
data(in page write cycle, the first byte data) is cancel invalid area.
WP input in this area becomes Don't care. Set the setup time to rise of D0 taken SCL 100ns or more. The area from the rise
of SCL to take in D0 to the end of internal automatic write (tWR) is cancel valid area. And, when it is set WP='H' during tWR,
write is ended forcibly, data of address under access is not guaranteed, therefore, write it once again. (Refer to Fig.50.) After
execution of forced end by WP, standby status gets in, so there is no need to wait for tWR (5ms at maximum).
? Rise of D0 taken clock
SCL
SCL
? Rise of SDA
SDA
D1
D0
ACK
SDA
D0
ACK
Enlarged view
Enlarged view
SDA
S
T Slave
A address
R
T
A
C Word
K address
L
A
C D7 D6 D5 D4 D3 D2 D1 D0
K
L
A
C
K
L
Data
A
C
K
L
S
T
O
P
tWR
WP
WP cancel invalid area
WP cancel valid area
Data is not written.
Write forced end
Data not guaranteed
Fig.50 WP valid timing
● Command cancel by start condition and stop condition
During command input, by continuously inputting start condition and stop condition, command can be cancelled.
(Refer to Fig. 51)
However, in ACK output area and during data read, SDA bus may output 'L', and in this case, start condition and stop
condition cannot be input, so reset is not available. Therefore, execute software reset. And when command is cancelled by
start, stop condition, during random read cycle, sequential read cycle, or current read cycle, internal setting address is not
determined, therefore, it is not possible to carry out current read cycle in succession. When to carry out read cycle in
succession, carry out random read cycle.
SCL
SDA
1
0
1
0
Start condition
Stop condition
Fig.51 Case of cancel by start, stop condition during slave address input
www.rohm.com
? 2009 ROHM Co., Ltd. All rights reserved.
15/40
2009.09 - Rev.D
相关PDF资料 |
PDF描述 |
|---|---|
| A3P060-1VQG100 | IC FPGA 1KB FLASH 60K 100-VQFP |
| A3P060-1VQ100 | IC FPGA 1KB FLASH 60K 100-VQFP |
| AGLN030V5-ZCSG81I | IC FPGA NANO 1KB 30K 81-CSP |
| AGL030V5-QNG132I | IC FPGA 1KB FLASH 30K 132-QFN |
| A3P030-QNG132I | IC FPGA 1KB FLASH 30K 132-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BR24L01AF-W | 制造商:ROHM Semiconductor 功能描述:IC,Memory,EEPROM,Serial SOP8 128x8 SERI |
| BR24L01AF-WE2 | 功能描述:电可擦除可编程只读存储器 2 WIRE SERIAL 1K (I2 C BUS TYPE) RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| BR24L01ANUX-WTR | 制造商:ROHM Semiconductor 功能描述:I2C BUS 1KBIT(128X8BIT) EEPROM, VSONX PKG, T/R - Tape and Reel 制造商:ROHM Semiconductor 功能描述:IC EEPROM 1KBIT 400KHZ 8VSON |
| BR24L01A-W | 功能描述:电可擦除可编程只读存储器 电可擦除可编程只读存储器s I2C BUS 1Kb RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| BR24L01A-W_07 | 制造商:ROHM 制造商全称:Rohm 功能描述:I2C BUS Serial EEPROMs |
发布紧急采购，3分钟左右您将得到回复。