- 您现在的位置：买卖IC网 > PDF目录255935 > BU-61840B3-200W (DATA DEVICE CORP) 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, PBGA128 PDF资料下载
参数资料
| 型号： | BU-61840B3-200W |
| 厂商： | DATA DEVICE CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, PBGA128 |
| 封装： | 0.815 X 0.815 INCH, 0.140 INCH HEIGHT, BGA-128 |
| 文件页数： | 26/60页 |
| 文件大小： | 763K |
| 代理商： | BU-61840B3-200W |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
32
Data Device Corporation
www.ddc-web.com
BU-6174X/6184X/6186X
D-03/02-250
MISCELLANEOUS
CLOCK INPUT
The Enhanced Mini-ACE decoder is capable of operating from a
10, 12, 16, or 20 MHz clock input. Depending on the configura-
tion of the specific model Enhanced Mini-ACE terminal, the
selection of the clock input frequency may be chosen by one of
either two methods. For all versions, the clock frequency may be
specified by means of the host processor writing to Configuration
Register #6. With the second method, which is applicable only for
the versions incorporating 4K (but not 64K) words of internal
RAM, the clock frequency may be specified by means of the
input signals that are otherwise used as the A15 and A14
address lines.
ENCODER/DECODERS
For the selected clock frequency, there is internal logic to derive
the necessary clocks for the Manchester encoder and decoders.
For all clock frequencies, the decoders sample the receiver out-
puts on both edges of the input clock. By in effect doubling the
decoders' sampling frequency, this serves to widen the tolerance
to zero-crossing distortion, and reduce the bit error rate.
For interfacing to fiber optic transceivers (e.g., for MIL-STD-1773
applications), the decoders are capable of operating with single-
ended, rather than double-ended, input signals. For applications
involving the use of single-ended transceivers, it is suggested
that you contact the factory at DDC regarding a transceiverless
version of the Enhanced Mini-ACE.
SELECTIVE MESSAGE MONITOR MEMORY
ORGANIZATION
A typical memory map for the ACE in the Selective Message
Monitor mode, assuming a 4K RAM space, is illustrated in
TABLE 45. This mode of operation defines several fixed locations
in the RAM. These locations are allocated in a way in which none
of them overlap with the fixed RT locations. This allows for the
combined RT/Selective Message Monitor mode.
The fixed memory map consists of two Monitor Command Stack
Pointers (locations 102 and 106 hex), two Monitor Data Stack
Pointers (locations 103 and 107 hex), and a Selective Message
Monitor Lookup Table (locations 0280 through 02FF hex).
For this example, the Monitor Command Stack size is assumed
to be 1K words, and the Monitor Data Stack size is assumed to
be 2K words.
FIGURE 11 illustrates the Selective Message Monitor operation.
Upon receipt of a valid Command Word, the Enhanced Mini-ACE
will reference the Selective Monitor Lookup Table to determine if
the current command is enabled. If the current command is dis-
abled, the Enhanced Mini-ACE monitor will ignore (and not store)
the current message. If the command is enabled, the monitor will
create an entry in the Monitor Command Stack at the address
location referenced by the Monitor Command Stack Pointer, and
an entry in the monitor data stack starting at the location refer-
enced by the Monitor Data Stack Pointer.
The format of the information in the data stack depends on the
format of the message that was processed. For example, for a
BC-to-RT transfer (receive command), the monitor will store the
command word in the monitor command descriptor stack, with
the data words and the receiving RT's status word stored in the
monitor data stack.
The size of the monitor command stack is programmable, with
choices of 256, 1K, 4K, or 16K words. The monitor data stack
size is programmable with choices of 512, 1K, 2K, 4K, 8K, 16K,
32K or 64K words.
Monitor Command Stack Pointer B (fixed location)
Monitor Data Stack A
0800-0FFF
Monitor Command Stack A
0400-07FF
Not Used
0300-03FF
Selective Monitor Lookup Table (fixed location)
0280-02FF
Not Used
0108-027F
Monitor Data Stack Pointer B (fixed location)
0107
Not Used
0104-0105
Monitor Data Stack Pointer A (fixed location)
0103
Monitor Command Stack Pointer A (fixed location)
0102
Not Used
0000-0101
DESCRIPTION
ADDRESS
(HEX)
0106
TABLE 45. TYPICAL SELECTIVE MESSAGE
MONITOR MEMORY MAP (shown for 4K RAM for
“Monitor only” mode)
Monitor Interrupts. Selective monitor interrupts may be issued
for End-of-message and for conditions relating to the monitor
command stack pointer and monitor data stack pointer. The lat-
ter, which are shown in FIGURE 9, include Command Stack 50%
Rollover, Command Stack 100% Rollover, Data Stack 50%
Rollover, and Data Stack 100% Rollover.
The 50% rollover interrupts may be used to inform the host
processor when the command stack or data stack is half full. At
that time, the host may proceed to read the received messages
in the upper half of the respective stack, while the Enhanced
Mini-ACE monitor writes messages to the lower half of the stack.
Later, when the monitor issues a 100% stack rollover interrupt,
the host can proceed to read the received data from the lower
half of the stack, while the Enhanced Mini-ACE monitor contin-
ues to write received data words to the upper half of the stack.
INTERRUPT STATUS QUEUE
Like the Enhanced Mini-ACE RT, the Selective Monitor mode
includes the capability for generating an interrupt status queue.
As illustrated in FIGURE 10, this provides a chronological histo-
ry of interrupt generating events. Besides the two Interrupt Mask
Registers, the Interrupt Status Queue provides additional filter-
ing capability, such that only valid messages and/or only invalid
messages may result in entries to the Interrupt Status Queue.
The interrupt status queue is 64 words deep, providing the capa-
bility to store entries for up to 32 monitored messages.
相关PDF资料 |
PDF描述 |
|---|---|
| BU-61840B3-200Y | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, PBGA128 |
| BU-61840B3-200Z | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, PBGA128 |
| BU-61840B3-202K | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, PBGA128 |
| BU-61840B3-302Q | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, PBGA128 |
| BU-61840B3-302S | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, PBGA128 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BU-61840B3NEW | 制造商:未知厂家 制造商全称:未知厂家 功能描述:MIL-STD-1553 Components |μ-ACE (Micro-ACE?) |
| BU-61843 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:MIL-STD-1553 Components |Enhanced Mini-ACE? |
| BU-61843F3-100 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Telecommunication IC |
| BU-61843F3-110 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Telecommunication IC |
| BU-61843F4-100 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Telecommunication IC |
发布紧急采购，3分钟左右您将得到回复。