- 您现在的位置：买卖IC网 > PDF目录11259 > BU4052BC (Rohm Semiconductor)IC MUX/DEMUX DUAL 4X1 16DIP PDF资料下载
参数资料
| 型号： | BU4052BC |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC MUX/DEMUX DUAL 4X1 16DIP |
| 标准包装： | 1,000 |
| 系列： | 4000B |
| 功能： | 多路复用器/多路分解器 |
| 电路： | 2 x 4:1 |
| 导通状态电阻： | 160 欧姆 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 18 V |
| 电流 - 电源： | 15µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 16-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-DIP |
| 包装： | 管件 |
Technical Note
BU4066BC,BU4066BCF,BU4066BCFV,BU4051BC,BU4051BCF,BU4051BCFV,BU4052BC,
BU4052BCF,BU4052BCFV,BU4053BC,BU4053BCF,BU4053BCFV,BU4551B,BU4551BF,BU4551BFV
15/17
www.rohm.com
2013.07 - Rev.C
2011 ROHM Co., Ltd. All rights reserved.
5)
BU4551B Series
PIN FUNCTION
PIN No.
PIN NAME
I/O
PIN FUNCTION
1
W1
I/O
Analog Switch Input / Output
2
X0
I/O
Analog Switch Input / Output
3
X1
I/O
Analog Switch Input / Output
4
X
I/O
Analog Switch Input / Output
5
Y
I/O
Analog Switch Input / Output
6
Y0
I/O
Analog Switch Input / Output
7
VEE
-
Power Supply(-)
8
VSS
-
Power Supply(-)
9
CONTROL
I
Control Input
10
Y1
I/O
Analog Switch Input / Output
11
Z0
I/O
Analog Switch Input / Output
12
Z1
I/O
Analog Switch Input / Output
13
Z
I/O
Analog Switch Input / Output
14
W
I/O
Analog Switch Input / Output
15
W0
I/O
Analog Switch Input / Output
16
VDD
-
Power Supply(+)
TRUTH TABLE
CONTROL
ON
SWITCH
0
W0,X0,Y0,Z0
1
W1,X1,Y1,Z1
●Notes for use
1. Absolute maximum ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can
break down the devices, thus making impossible to identify breaking mode, such as short circuit or an open circuit. If any
over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as
fuses.
2. Connecting the power supply connector backward
Connecting of the power supply in reverse polarity can damage IC. Take precautions when connecting the power supply
lines. An external direction diode can be added.
3. Power Supply lines
Design PCB layout pattern to provide low impedance GND and supply lines. To obtain a low noise ground and supply line,
separate the ground section and supply lines of the digital and analog blocks. Furthermore, for all power terminals to ICs,
connect a capacitor between the power supply and the GND terminal. When applying electrolytic capacitors in the circuit,
not that capacitance characteristic values are reduced at low temperatures.
4. GND voltage
The potential of GND pin must be minimum potential in all operating conditions.
5. Thermal design
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions.
6. Inter-pin shorts and mounting errors
Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any
connection error or if pins are shorted together.
7. Actions in strong electromagnetic field
Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to
malfunction.
8. Testing on application boards
When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress.
Always discharge capacitors after each process or step. Always turn the IC's power supply off before connecting it to or
remove it from a jig or fixture during the inspection process. Ground the IC during assembly steps as an antistatic measure.
Use similar precaution when transporting or storing the IC.
9.Ground Wiring Pattern
When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns,
placing a signal ground point at the ground potential of application so that the pattern wiring resistance and voltage
variations caused by large currents do not caused by large currents do not cause variations in the small signal ground
voltage. Be careful not to change the GND wiring pattern of any external components, either.
1
2
3
4
5
6
7
16
15
14
13
12
11
10
VDD
W0
W
Z
Z1
Z0
Y1
8
9 CONTROL
X0
X1
X
Y
Y0
VEE
Z
Z1
1Y
CONTROL
W1
X0
X1
X
Y0
VEE
VSS
Y
W0
W
Z0
Y1
CONTROL
LEVEL
CONVERTER
VDD
CONT
VSS
VEE
W0
W1
X0
X1
Y0
Y1
Z0
Z1
COMMON
W
COMMON
X
COMMON
Y
COMMON
Z
相关PDF资料 |
PDF描述 |
|---|---|
| PIC17C756A-16/PT | IC MCU OTP 16KX16 A/D PWM 64TQFP |
| BU4051BC | IC MUX/DEMUX 8X1 16DIP |
| BU4551BF-E2 | IC MUX/DEMUX QUAD 1X2 16SOP |
| BU4053BC | IC MUX/DEMUX TRIPLE 2X1 16DIP |
| BU4066BC | IC SWITCH QUAD 1X1 14DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BU4052BC/BCF/BCFV | 制造商:ROHM 制造商全称:Rohm 功能描述:Standard LSIs |
| BU4052BC-E2 | 制造商:ROHM 制造商全称:Rohm 功能描述:High Voltage CMOS Logic ICs |
| BU4052BCF | 制造商:ROHM 功能描述:SOP16 SM IC-CMOS LOGIC ANALOG MULTIPLEXER/DEMULT DIFFERENTIAL 4-CHANNEL 制造商:ROHM 功能描述:SOP16 SM IC-CMOS LOGIC ANALOG MULTIPLEXER/DEMULT DIFFERENTIAL 4-CHANNEL - free partial T/R at 500. 制造商:Panasonic Industrial Company 功能描述:IC |
| BU4052BCF-E2 | 功能描述:多路器开关 IC DUAL 4 CH ANALOG MULTIPLEXER RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| BU4052BCFV | 制造商:ROHM 制造商全称:Rohm 功能描述:High Voltage CMOS Logic ICs |
发布紧急采购，3分钟左右您将得到回复。