- 您现在的位置：买卖IC网 > PDF目录227782 > BU4247F 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4 PDF资料下载
参数资料
| 型号： | BU4247F |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4 |
| 封装： | ROHS COMPLIANT, SOP-4 |
| 文件页数： | 11/11页 |
| 文件大小： | 282K |
| 代理商： | BU4247F |
Technical Note
9/10
BU42
□□G, BU42□□F, BU42□□FVE, BU43□□G, BU43□□F, BU43□□FVE series
www.rohm.com
2009.06 - Rev.B
2009 ROHM Co., Ltd. All rights reserved.
13.
Delay time (tPLH)
tPLH =
τ × RCT × CCT (sec)
τ: time constant
RCT : 10M
(typ.) (built-in resistor)
CCT : capacitor connected CT pin.
Recommended value of CCT capacitor is over 100pF.
The reference value
(
τ × RCT) ×10
6
VDET = 0.9 to 2.5V
Ta = 25°C
(min. = 5.1 × 10
6
typ.= 6.0 × 10
6
max = 6.9 × 10
6)
Ta = -25 to 125°C
(min. = 3.3 × 10
6
typ. = 6.0 × 10
6
max = 8.7 × 10
6)
VDET = 2.6 to 4.8V
Ta = 25°C
(min. = 5.9 × 10
6
typ.= 6.9 × 10
6
max = 7.9 × 10
6)
Ta = -25 to 125°C
(min. = 3.8 × 10
6
typ.= 6.9 × 10
6
max = 10.0 × 10
6)
14. External parameters
The recommended parameter range for CT is 100pF~0.1F. For RL, the recommended range is 50k
~1M. There
are many factors (board layout, etc) that can affect characteristics. Please verify and confirm using practical applications.
15. CT pin discharge
Due to the capabilities of the CT pin discharge transistor, the CT pin may not completely discharge when a short input
pulse is applied, and in this case the delay time may not be controlled. Please verify the actual operation.
16. Power on reset operation
Please note that the power on reset output varies with the Vcc rise up time. Please verify the actual operation.
17. Precautions for board inspection
Connecting low-impedance capacitors to run inspections with the board may produce stress on the IC.
Therefore, be certain to use proper discharge procedure before each process of the test operation.
To prevent electrostatic accumulation and discharge in the assembly process, thoroughly ground yourself and any
equipment that could sustain ESD damage, and continue observing ESD-prevention procedures in all handing, transfer
and storage operations. Before attempting to connect components to the test setup, make certain that the power supply is
OFF. Likewise, be sure the power supply is OFF before removing any component connected to the test setup.
18. When the power supply, is turned on because of in certain cases, momentary Rash-current flow into the IC at the logic
unsettled, the couple capacitance, GND pattern of width and leading line must be considered.
相关PDF资料 |
PDF描述 |
|---|---|
| BZV26/B0321/92 | 3A, 250VAC, MALE, MAINS POWER CONNECTOR |
| BZV26/B0321/93 | 3A, 250VAC, MALE, MAINS POWER CONNECTOR |
| BZV26/B0321/94 | 3A, 250VAC, MALE, MAINS POWER CONNECTOR |
| BZV26/B0321/95 | 3A, 250VAC, MALE, MAINS POWER CONNECTOR |
| BZV26/B0321/96 | 3A, 250VAC, MALE, MAINS POWER CONNECTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BU4247F-TR | 功能描述:电压监测器/监控器 LOW VOLT DETEC VOLT 0.9V RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| BU4247FVE | 制造商:ROHM 制造商全称:Rohm 功能描述:Low Voltage Detector IC with Adjustable Output Delay |
| BU4247FVE-TR | 功能描述:电压监测器/监控器 LOW VOLT DETEC VOLT 0.9V RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| BU4247G | 制造商:ROHM 制造商全称:Rohm 功能描述:Low Voltage Detector IC with Adjustable Output Delay |
| BU4247G-TR | 功能描述:电压监测器/监控器 CMOS LOW VOLT DETEC RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。