收藏本站
参数资料
型号： C8051F015R
厂商： Silicon Laboratories Inc
文件页数： 167/171页
文件大小： 0K
描述： IC 8051 MCU 32K FLASH 64TQFP
标准包装： 1
系列： C8051F01x
核心处理器： 8051
芯体尺寸： 8-位
速度： 25MHz
连通性： SMBus（2 线/I²C），SPI，UART/USART
外围设备： 欠压检测/复位，POR，PWM，温度传感器，WDT
输入/输出数： 32
程序存储器容量： 32KB（32K x 8）
程序存储器类型： 闪存
RAM 容量： 2.25K x 8
电压 - 电源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
数据转换器： A/D 8x10b; D/A 2x12b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 64-TQFP
包装： 剪切带 (CT)
其它名称： 336-1030-1
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
13.4.
External Reset
The external /RST pin provides a means for external circuitry to force the MCU into a reset state. Asserting an
active-low signal on the /RST pin will cause the MCU to enter the reset state. Although there is a weak internal
pullup, it may be desirable to provide an external pull-up and/or decoupling of the /RST pin to avoid erroneous
noise-induced resets. The MCU will remain in reset until at least 12 clock cycles after the active-low /RST signal is
removed. The PINRSF flag (RSTSRC.0) is set on exit from an external reset. The /RST pin is also 5V tolerant.
13.5.
Missing Clock Detector Reset
The Missing Clock Detector is essentially a one-shot circuit that is triggered by the MCU system clock. If the
system clock goes away for more than 100
s, the one-shot will time out and generate a reset. After a Missing Clock
Detector reset, the MCDRSF flag (RSTSRC.2) will be set, signifying the MSD as the reset source; otherwise, this
bit reads 0. The state of the /RST pin is unaffected by this reset. Setting the MSCLKE bit in the OSCICN register
(see Figure 14.2) enables the Missing Clock Detector.
13.6.
Comparator 0 Reset
Comparator 0 can be configured as an active-low reset input by writing a 1 to the C0RSEF flag (RSTSRC.5).
Comparator 0 should be enabled using CPT0CN.7 (see Figure 8.3) at least 20
s prior to writing to C0RSEF to
prevent any turn-on chatter on the output from generating an unwanted reset. When configured as a reset, if the
non-inverting input voltage (on CP0+) is less than the inverting input voltage (on CP0-), the MCU is put into the
reset state. After a Comparator 0 Reset, the C0RSEF flag (RSTSRC.5) will read 1 signifying Comparator 0 as the
reset source; otherwise, this bit reads 0. The state of the /RST pin is unaffected by this reset. Also, Comparator 0
can generate a reset with or without the system clock.
13.7.
External CNVSTR Pin Reset
The external CNVSTR signal can be configured as an active-low reset input by writing a 1 to the CNVRSEF flag
(RSTSRC.6). The CNVSTR signal can appear on any of the P0, P1, or P2 I/O pins as described in Section 15.1.
(Note that the Crossbar must be configured for the CNVSTR signal to be routed to the appropriate Port I/O.) The
Crossbar should be configured and enabled before the CNVRSEF is set to configure CNVSTR as a reset source.
When configured as a reset, CNVSTR is active-low and level sensitive. After a CNVSTR reset, the CNVRSEF flag
(RSTSRC.6) will read 1 signifying CNVSTR as the reset source; otherwise, this bit reads 0. The state of the /RST
pin is unaffected by this reset.
13.8.
Watchdog Timer Reset
The MCU includes a programmable Watchdog Timer (WDT) running off the system clock. The WDT will force
the MCU into the reset state when the watchdog timer overflows. To prevent the reset, the WDT must be restarted
by application software before the overflow occurs. If the system experiences a software/hardware malfunction
preventing the software from restarting the WDT, the WDT will overflow and cause a reset. This should prevent
the system from running out of control.
The WDT is automatically enabled and started with the default maximum time interval on exit from all resets. If
desired the WDT can be disabled by system software or locked on to prevent accidental disabling. Once locked, the
WDT cannot be disabled until the next system reset. The state of the /RST pin is unaffected by this reset.
95
Rev. 1.7
相关PDF资料
PDF描述
C8051F017R IC 8051 MCU 32K FLASH 32LQFP
C8051F007R IC 8051 MCU 32K FLASH 32LQFP
C8051F221R IC 8051 MCU 8K FLASH 32LQFP
C8051F220R IC 8051 MCU 8K FLASH 48TQFP
C8051F012R IC 8051 MCU 32K FLASH 32LQFP
相关代理商/技术参数
参数描述
C8051F015TB 功能描述:开发板和工具包 - 8051 USE 634-C8051F005TB RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压:
C8051F015-TB 功能描述:BOARD PROTOTYPING W/C8051F015 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035
C8051F016 功能描述:8位微控制器 -MCU 32KB 10ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F016-GQ 功能描述:8位微控制器 -MCU 32KB 10ADC 48P MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F016-GQR 功能描述:8位微控制器 -MCU 32KB 10ADC 48Pin MCU Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*