- 您现在的位置：买卖IC网 > PDF目录17156 > C8051F930DK (Silicon Laboratories Inc)KIT DEV C8051F920,F921,F930,F931 PDF资料下载
参数资料
| 型号： | C8051F930DK |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 13/25页 |
| 文件大小： | 0K |
| 描述： | KIT DEV C8051F920,F921,F930,F931 |
| 产品培训模块： | C8051F9xx Lower Power MCUs |
| 视频文件： | Designing for Low Power Operation |
| 特色产品： | C8051F91x/0x MCU Series Development Kit |
| 标准包装： | 1 |
| 类型： | MCU |
| 适用于相关产品： | C8051F920，F921，F930，F931 |
| 所含物品： | 目标板，电源适配器，USB 调试适配器，线缆，电池以及软件 |
| 产品目录页面： | 626 (CN2011-ZH PDF) |
| 相关产品： | 336-1471-ND - IC 8051 MCU 32K FLASH 24-QFN 336-1470-ND - IC 8051 MCU 32K FLASH 32-QFN 336-1469-ND - IC 8051 MCU 32K FLASH 32-LQFP 336-1468-ND - IC 8051 MCU 64K FLASH 24-QFN 336-1467-ND - IC 8051 MCU 64K FLASH 32-QFN 336-1466-ND - IC 8051 MCU 64K FLASH 32-LQFP |
| 其它名称： | 336-1473 |
C8051F93x/92x
5.2. Target Board Power Options and Current Measurement
The C8051F930 Target Board supports three power options, selectable by the three-way header (J10/J11). The
power options vary based on the configuration (one-cell or two-cell mode) selected by SW4. Power to the MCU
may be switched on/off using the power switch (SW5). Important Note: The power switch (SW5) must be in the
OFF position prior to switching between one-cell and two-cell mode using SW4. The power options are
described in the paragraphs below.
5.2.1. Wall Power
When the J10/J11 three-way header is set to WALL_PWR, the C8051F930 Target Board may be powered from the
following power sources:
?? 9
VDC power using the ac to dc power adapter (P2)
?? 5 VDC USB VBUS power from PC via the USB Debug Adapter (J9)
?? 5 VDC USB VBUS power from PC via the CP2103 USB connector (P3)
All the three power sources are ORed together using reverse-biased diodes (D1, D2, D3), eliminating the need for
headers to choose between the sources. The target board will operate as long as any one of the power sources is
present. The ORed power is regulated to a 3.3 V dc voltage using a LDO regulator (U2). The output of the regulator
powers the +3 VD net on the target board.
If SW4 is configured to select two-cell mode, the VBAT supply net on the target board is powered directly from the
+3 VD net. If SW4 is configured to select one-cell mode, the VBAT supply net is powered directly from the +1 VD.
This power supply net takes +3 VD and passes it through a 1.65 V LDO. The LDO’s output voltage is variable and
can be set by changing the value of resistor R32.
J11
COIN_CELL
AAA_BAT
VBAT
WALL_PWR
5.2.2. AAA Battery
When the J10/J11 three-way header is set to AAA_BAT, the C8051F930 Target Board may be powered from a
single AAA battery inserted in BT1 or from the series combination of the AAA batteries inserted in BT1 and BT2. A
single battery is selected when SW4 is configured to one-cell mode. The two AAA batteries configured in series to
provide a voltage of ~3 V are selected when SW4 is configured to two-cell mode.
J11
COIN_CELL
AAA_BAT
VBAT
WALL_PWR
5.2.3. Coin Cell Battery
When the J10/J11 three-way header is set to COIN_CELL, the C8051F930 Target Board may be powered from a
single 1.5 V Alkaline (A76) or Silver Oxide (357) button cell inserted in BT4 or from a single 3 V Lithium (CR2032)
coin cell inserted in BT3. The button cell (BT4) is selected when SW4 is configured to one-cell mode, and the coin
cell (BT3) is selected when SW4 is configured to two-cell mode.
J11
COIN_CELL
AAA_BAT
VBAT
WALL_PWR
5.2.4. Measuring Current
The header (J17) and terminal block (H2) provide a way to measure the total supply current flowing from the power
supply source to the MCU. The measured current does not include any current from the VBAT LED (DS2), the
address latch (U4) or the quiescent current from the power supply; however, it does include the current used by
any LEDs powered from the VDD/DC+ supply net or sourced through a GPIO pin. See the target board schematic
in Figure 11 through Figure 13 for additional information.
Rev. 0.6
13
相关PDF资料 |
PDF描述 |
|---|---|
| RD3803MMA7660FC | KIT EVAL BOARD MMA7660FC |
| EBM36DSXH | CONN EDGECARD 72POS DIP .156 SLD |
| MIC4452ZT | IC DRIVR MOSF 12A LOSIDE TO220-5 |
| MIC4104YM | IC MOSFET DRIVER 100V TTL 8-SOIC |
| C8051F350DK | DEV KIT FOR F350/351/352/353 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| C8051F930-F-G1DI | 制造商:Silicon Laboratories Inc 功能描述:MCU - Gel-pak, waffle pack, wafer, diced wafer on film |
| C8051F930-F-GM | 制造商:Silicon Laboratories Inc 功能描述:64KB,10ADC,32PIN MCU - Rail/Tube 制造商:Silicon Laboratories Inc 功能描述:MCU 64KB FLASH 10BIT ADC 32QFN |
| C8051F930-F-GMR | 制造商:Silicon Laboratories Inc 功能描述:64KB,10ADC,32PIN MCU - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC MCU 64KB FLASH 32QFN |
| C8051F930-F-GQ | 制造商:Silicon Laboratories Inc 功能描述:64KB,10ADC,32PIN MCU - Trays 制造商:Silicon Laboratories Inc 功能描述:MCU 64KB FLASH 10BIT ADC 32LQFP |
| C8051F930-F-GQR | 制造商:Silicon Laboratories Inc 功能描述:64KB,10ADC,32PIN MCU - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC MCU 64KB FLASH 32LQFP |
发布紧急采购，3分钟左右您将得到回复。