- 您现在的位置：买卖IC网 > PDF目录375652 > C930KGKT (光宝科技股份有限公司) LITE-ON TECHNOLOGY CORPORATION PDF资料下载
参数资料
| 型号： | C930KGKT |
| 厂商： | 光宝科技股份有限公司 |
| 英文描述： | LITE-ON TECHNOLOGY CORPORATION |
| 中文描述： | 光宝科技股份有限公司 |
| 文件页数： | 9/11页 |
| 文件大小： | 641K |
| 代理商： | C930KGKT |
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Part No. : LTST-C930KGKT
Page : 9 of 11
BNS-OD-C131/A4
CAUTIONS
1. Application
The LEDs described here are intended to be used for ordinary electronic equipment (such as office
equipment, communication equipment and household applications).Consult Liteon’s Sales in advance
for information on applications in which exceptional reliability is required, particularly when the failure
or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation,
traffic control equipment, medical and life support systems and safety devices).
2. Storage
The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity.
It is recommended that LEDs out of their original packaging are IR-reflowed within one week.
For extended storage out of their original packaging, it is recommended that the LEDs be stored in a
sealed container with appropriate desiccant, or in a desiccators with nitrogen ambient.
LEDs stored out of their original packaging for more than a week should be baked at about 60 deg C
for at least 24 hours before solder assembly.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary.
4. Soldering
Recommended soldering conditions:
Reflow soldering
Wave Soldering
Pre-heat
Pre-heat time
Peak temperature
Soldering time
10 sec. Max.
Soldering time
5. Drive Method
An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs
connected in parallel in an application, it is recommended that a current limiting resistor be incorporated
in the drive circuit, in series with each LED as shown in Circuit A below.
Soldering iron
120~150°C
120 sec. Max.
240°C Max.
Pre-heat
Pre-heat time
Solder wave
100°C Max.
60 sec. Max.
260°C Max.
10 sec. Max.
Temperature
Soldering time
300°C Max.
3 sec. Max.
(one time only)
Circuit model A
Circuit model B
LED
LED
(A) Recommended circuit.
(B) The brightness of each LED might appear different due to the differences in the I-V characteristics
of those LEDs.
6. ESD (Electrostatic Discharge)
Static Electricity or power surge will damage the LED.
Suggestions to prevent ESD damage:
Use of a conductive wrist band or anti-electrostatic glove when handling these LEDs.
All devices, equipment, and machinery must be properly grounded.
Work tables, storage racks, etc. should be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of the LED’s
plastic lens as a result of friction between LEDs during storage and handling.
相关PDF资料 |
PDF描述 |
|---|---|
| C983 | LED RED SURFACE MOUNT 0805 |
| C900 | CHANNEL PHOTO MULTIPLIER |
| C911 | CHANNEL PHOTO MULTIPLIER |
| C911P | CHANNEL PHOTO MULTIPLIER |
| C921 | CHANNEL PHOTO MULTIPLIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| C930ZG35500RA0X | 制造商:KEMET Corporation 功能描述:FILM CAPACITOR |
| C930ZG35500ZA0X | 制造商:KEMET Corporation 功能描述:FILM CAPACITOR |
| C930ZG35500ZACX | 制造商:KEMET Corporation 功能描述:FILM CAPACITOR |
| C930ZG35500ZB0J | 制造商:KEMET Corporation 功能描述:FILM CAPACITOR |
| C930ZG35526ZACX | 制造商:KEMET Corporation 功能描述:FILM CAPACITOR |
发布紧急采购，3分钟左右您将得到回复。