- 您现在的位置：买卖IC网 > PDF目录15171 > CAT1025WI-45-GT3 (ON Semiconductor)IC SUPERVISR CPU 2K EEPROM 8SOIC PDF资料下载
参数资料
| 型号： | CAT1025WI-45-GT3 |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISR CPU 2K EEPROM 8SOIC |
| 标准包装： | 3,000 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 130 ms |
| 电压 - 阀值： | 4.5V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
CAT1024, CAT1025
ACKNOWLEDGE
After a successful data transfer, each receiving
device is required to generate an acknowledge. The
acknowledging device pulls down the SDA line
during the ninth clock cycle, signaling that it received
the 8 bits of data.
The CAT1024/25 responds with an acknowledge
after receiving a START condition and its slave
address. If the device has been selected along with
a write operation, it responds with an acknowledge
after receiving each 8-bit byte.
When the CAT1024/25 begins a READ mode it
transmits 8 bits of data, releases the SDA line and
monitors the line for an acknowledge. Once it
receives this acknowledge, the CAT1024/25 will
continue to transmit data. If no acknowledge is sent
by the Master, the device terminates data transmis–
sion and waits for a STOP condition.
Figure 5. Start/Stop Timing
SDA
SCL
START BIT
Figure 6. Acknowledge Timing
WRITE OPERATIONS
Byte Write
ˉ ˉ
In the Byte Write mode, the Master device sends the
START condition and the slave address information
(with the R/W bit set to zero) to the Slave device. After
the Slave generates an acknowledge, the Master sends
a 8-bit address that is to be written into the address
pointers of the device. After receiving another acknow-
ledge from the Slave, the Master device transmits the
data to be written into the addressed memory location.
The CAT1024/25 acknowledges once more and the
Master generates the STOP condition. At this time, the
device begins an internal programming cycle to non-
volatile memory. While the cycle is in progress,
the device will not respond to any request from the
Master device.
STOP BIT
SCL FROM
MASTER
1
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
Figure 7: Slave Address Bits
START
ACKNOWLEDGE
Default Configuration
1
0
1
0
0
0
0
R/W
Doc. No. MD-3008 Rev. R
10
? 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6401CRZ-T | IC REG CTRLR BST FLYBK ISO 16QFN |
| RYM15DRST | CONN EDGECARD 30POS DIP .156 SLD |
| CAT1021WI-45-GT3 | IC SUPERVISR CPU 2K EEPROM 8SOIC |
| ISL6401CBZ-T | IC REG CTRLR PWM CM 14-SOIC |
| CAT1027WI-28-GT3 | IC SUPERVISR CPU 2K EEPROM 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT1025WI-45-T3 | 功能描述:监控电路 CPU w/2K RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| CAT1025YI25 | 功能描述:监控电路 2K bit 2.5V Ind Temp RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| CAT1025YI-25-GT3 | 功能描述:监控电路 CPU SUP W/2K EEPROM RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| CAT1025YI-25-T3 | 制造商:ON Semiconductor 功能描述:CPU SUPERVISOR WITH 2K EEPROM - Tape and Reel |
| CAT1025YI-25TE13 | 功能描述:监控电路 2K bit 2.5V Ind Temp RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。