参数资料
型号: CAT140089SWI-GT3
厂商: ON Semiconductor
文件页数: 8/14页
文件大小: 0K
描述: IC SUPERVISOR 8KBIT 2.85V 8SOIC
标准包装: 1
类型: 简单复位/加电复位
监视电压数目: 1
输出: 推挽式,图腾柱
复位: 低有效
复位超时: 最小为 140 ms
电压 - 阀值: 2.93V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SOIC
包装: 标准包装
其它名称: CAT140089SWI-GT3DKR
CAT140xx
WRITE OPERATIONS
Byte Write
In Byte Write mode, the Master sends the START
condition and the Slave address with the R/W bit set
to zero to the Slave. After the Slave generates an
acknowledge, the Master sends the byte address that
is to be written into the address pointer of the
CAT140xx. After receiving another acknowledge from
the Slave, the Master transmits the data byte to be
written into the addressed memory location. The
CAT140xx device will acknowledge the data byte and
the Master generates the STOP condition, at which
time the device begins its internal Write cycle to
nonvolatile memory (Figure 7). While this internal
cycle is in progress (t WR ), the SDA output will be tri-
stated and the CAT140xx will not respond to any
request from the Master device (Figure 8).
Page Write
The CAT140xx writes up to 16 bytes of data in a
single write cycle, using the Page Write operation
(Figure 9). The Page Write operation is initiated in the
same manner as the Byte Write operation, however
instead of terminating after the data byte is
transmitted, the Master is allowed to send up to fifteen
additional bytes. After each byte has been transmitted
the CAT140xx will respond with an acknowledge and
internally increments the four low order address bits.
The high order bits that define the page address
remain unchanged. If the Master transmits more than
sixteen bytes prior to sending the STOP condition, the
address counter ‘wraps around’ to the beginning of
page and previously transmitted data will be
overwritten. Once all sixteen bytes are received and
the STOP condition has been sent by the Master, the
internal Write cycle begins. At this point all received
data is written to the CAT140xx in a single write cycle.
Acknowledge Polling
The acknowledge (ACK) polling routine can be used
to take advantage of the typical write cycle time.
Once the stop condition is issued to indicate the end
of the host’s write operation, the CAT140xx initiates
the internal write cycle. The ACK polling can be
initiated immediately. This involves issuing the start
condition followed by the slave address for a write
operation. If the CAT140xx is still busy with the write
operation, NoACK will be returned. If the CAT140xx
has completed the internal write operation, an ACK
will be returned and the host can then proceed with
the next read or write operation.
Doc. No. MD-1117 Rev. B
8
? 2008 SCILLC. All rights reserved.
Characteristics subject to change without notice
相关PDF资料
PDF描述
CAT1232LPZ-GT3 IC SUPERVISOR MPU 5V 8MSOP
CAT1832Z-GT3 IC SUPERVISOR MPU 3.3V 8MSOP
CAT140049TWI-GT3 IC SUPERVISOR I2C EEPROM 8SOIC
CAT140049SWI-GT3 IC SUPERVISOR I2C EEPROM 8SOIC
CAT823MSDI-GT3 IC SUPERVISOR RESET SC70-5
相关代理商/技术参数
参数描述
CAT140089TWI-GT3 功能描述:监控电路 w/8k I2C RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
CAT140169MWI-GT3 功能描述:监控电路 SUP WITH 8K I2C EEPROM RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
CAT140169SWI-GT3 功能描述:监控电路 SUP WITH 8K I2C EEPROM RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
CAT140169TWI-GT3 制造商:ON Semiconductor 功能描述:SUPERVISOR WITH 8K I2C EEPROM - Tape and Reel
CAT-1-456401-7 制造商:Samtec Inc 功能描述:CAT - Bulk