- 您现在的位置：买卖IC网 > PDF目录5043 > CAT1641WI-28-T3 (ON Semiconductor)IC SUPERVISOR W/MEM 2.85V 8SOIC PDF资料下载
参数资料
| 型号： | CAT1641WI-28-T3 |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/18页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR W/MEM 2.85V 8SOIC |
| 标准包装： | 1 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效 |
| 复位超时： | 最小为 130 ms |
| 电压 - 阀值： | 2.85V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 标准包装 |
| 其它名称： | CAT1641WI-28-T3DKR CAT1641WI-28-TE13DKR CAT1641WI-28-TE13DKR-ND |
CAT1640, CAT1641
EMBEDDED EEPROM OPERATON
The CAT1640 and CAT1641 feature a 64 kbit embedded
serial EEPROM that supports the I 2 C Bus data transmission
protocol. This Inter ? Integrated Circuit Bus protocol defines
any device that sends data to the bus to be a transmitter and
any device receiving data to be a receiver. The transfer is
controlled by the Master device which generates the serial
clock and all START and STOP conditions for bus access.
Both the Master device and Slave device can operate as
either transmitter or receiver, but the Master device controls
which mode is activated.
I 2 C Bus Protocol
The features of the I 2 C bus protocol are defined as
follows:
1. Data transfer may be initiated only when the bus is
not busy.
2. During a data transfer, the data line must remain
stable whenever the clock line is high. Any
changes in the data line while the clock line is high
will be interpreted as a START or STOP condition.
Start Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of SDA
when SCL is HIGH. The CAT1640/41 monitors the SDA
and SCL lines and will not respond until this condition is
met.
Stop Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
DEVICE ADDRESSING
The Master begins a transmission by sending a START
condition. The Master sends the address of the particular
slave device it is requesting. The four most significant bits
of the 8 ? bit slave address are programmable in metal and the
default is 1010.
The last bit of the slave address specifies whether a Read
or Write operation is to be performed. When this bit is set to
1, a Read operation is selected, and when set to 0, a Write
operation is selected.
SCL
After the Master sends a START condition and the slave
address byte, the CAT1640/41 monitors the bus and
responds with an acknowledge (on the SDA line) when its
address matches the transmitted slave address. The
CAT1640/41 then perform a Read or Write operation
depending on the R/W bit.
SDA
8TH BIT
BYTE n
ACK
tWR
STOP
CONDITION
Figure 4. Write Cycle Timing
ACKNOWLEDGE
START
CONDITION
ADDRESS
After a successful data transfer, each receiving device is
required to generate an acknowledge. The acknowledging
device pulls down the SDA line during the ninth clock cycle,
signaling that it received the 8 bits of data.
The CAT1640/41 responds with an acknowledge after
receiving a START condition and its slave address. If the
When the CAT1640/41 begins a READ mode it transmits
8 bits of data, releases the SDA line and monitors the line for
an acknowledge. Once it receives this acknowledge, the
CAT1640/41 will continue to transmit data. If no
acknowledge is sent by the Master, the device terminates
data transmission and waits for a STOP condition.
device has been selected along with a write operation, it
responds with an acknowledge after receiving each 8 ? bit
byte.
http://onsemi.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| P1330-224K | INDUCTOR POWER 220.0UH SMD |
| CAT1640WI-42-T3 | IC SUPERVISOR W/MEM 4.25V 8SOIC |
| P1330R-224K | INDUCTOR POWER 220.0UH SMD |
| CAT1320WI-42-T3 | IC SUPERVISOR W/MEM 4.25V 8SOIC |
| P1330R-184K | INDUCTOR POWER 180.0UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT1641WI-28-TE13 | 制造商:Catalyst Semiconductor 功能描述: |
| CAT1641WI30 | 功能描述:监控电路 CPU w/64K RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| CAT1641WI-30-G | 功能描述:监控电路 CPU w/64K RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| CAT1641WI-30-GT3 | 功能描述:监控电路 CPU SUP W/64K EEPROM RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| CAT1641WI-30-T3 | 功能描述:监控电路 CPU w/64K RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。