- 您现在的位置：买卖IC网 > PDF目录256923 > CAT24WC16JE-TE13 2K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 PDF资料下载
参数资料
| 型号： | CAT24WC16JE-TE13 |
| 元件分类： | PROM |
| 英文描述： | 2K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| 封装： | SOIC-8 |
| 文件页数： | 4/10页 |
| 文件大小： | 411K |
| 代理商： | CAT24WC16JE-TE13 |
CAT24WC01/02/04/08/16
3
Doc. No. 1022, Rev. J
A.C. CHARACTERISTICS
VCC = +1.8V to +6.0V, unless otherwise specified.
Read & Write Cycle Limits
Symbol
Parameter
1.8V-6.0V, 2.5V-6.0V
4.5V-5.5V
Min.
Max.
Min.
Max.
Units
FSCL
Clock Frequency
100
400
kHz
TI(1)
Noise Suppression Time
200
ns
Constant at SCL, SDA Inputs
tAA
SCL Low to SDA Data Out
3.5
1
s
and ACK Out
tBUF(1)
Time the Bus Must be Free Before
4.7
1.2
s
a New Transmission Can Start
tHD:STA
Start Condition Hold Time
4
0.6
s
tLOW
Clock Low Period
4.7
1.2
s
tHIGH
Clock High Period
4
0.6
s
tSU:STA
Start Condition Setup Time
4.7
0.6
s
(for a Repeated Start Condition)
tHD:DAT
Data In Hold Time
0
ns
tSU:DAT
Data In Setup Time
50
ns
tR(1)
SDA and SCL Rise Time
1
0.3
s
tF(1)
SDA and SCL Fall Time
300
ns
tSU:STO
Stop Condition Setup Time
4
0.6
s
tDH
Data Out Hold Time
100
ns
Note:
(1) This parameter is tested initially and after a design or process change that affects the parameter.
(2) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated.
The write cycle time is the time from a valid stop
condition of a write sequence to the end of the internal
program/erase cycle. During the write cycle, the bus
interface circuits are disabled, SDA is allowed to remain
high, and the device does not respond to its slave
address.
Write Cycle Limits
Symbol
Parameter
Min.
Typ.
Max
Units
tWR
Write Cycle Time
10
ms
Power-Up Timing(1)(2)
Symbol
Parameter
Max.
Units
tPUR
Power-up to Read Operation
1
ms
tPUW
Power-up to Write Operation
1
ms
相关PDF资料 |
PDF描述 |
|---|---|
| CAT24WC16JI-1.8 | 2K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| CAT24WC64PE-REVB | 8K X 8 I2C/2-WIRE SERIAL EEPROM, PDIP8 |
| CAT24WC64XA-TE13REVB | 8K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| CAT28F010H14I-90TE13 | 128K X 8 FLASH 12V PROM, 90 ns, PDSO32 |
| CAT25040PI-1.8REV-C | 512 X 8 SPI BUS SERIAL EEPROM, PDIP8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT24WC16JI | 功能描述:电可擦除可编程只读存储器 (2048x8) 16k RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| CAT24WC16JI-1.8 | 功能描述:电可擦除可编程只读存储器 (2048x8) 16k RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| CAT24WC16JI-TE13 | 制造商:CLYST 功能描述: |
| CAT24WC16L | 功能描述:电可擦除可编程只读存储器 (2048x8) 16k RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| CAT24WC16L-1.8 | 功能描述:电可擦除可编程只读存储器 (2048x8) 16k RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。