- 您现在的位置：买卖IC网 > Datasheet目录968 > CAT3649AGEVB (ON Semiconductor)BOARD EVALUATION FOR CAT3649 Datasheet资料下载
参数资料
| 型号： | CAT3649AGEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/14页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR CAT3649 |
| 设计资源： | CAT3649AGEVB Schematic CAT3649AGEVB BOM |
| 标准包装： | 1 |
| 系列： | QUAD-Mode® |
| 电流 - 输出 / 通道： | 25mA |
| 输出及类型： | 6，非隔离 |
| 特点： | 亮度控制 |
| 输入电压： | 3.3V，5V |
| 已供物品： | 板 |
| 已用 IC / 零件： | CAT3649 |
| 其它名称： | CAT3649AGEVBOS |
CAT3649
Table 5. PIN DESCRIPTION
Pin No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
TAB
Name
C1+
C1 ?
C2+
C2 ?
GND
LED1
LED2
LED3
LED4
LED5
LED6
ADIM
PWM
CPWM
VOUT
VIN
GND
Function
Bucket capacitor 1 Positive terminal
Bucket capacitor 1 Negative terminal
Bucket capacitor 2 Positive terminal
Bucket capacitor 2 Negative terminal
Ground Reference
LED1 cathode terminal.
LED2 cathode terminal.
LED3 cathode terminal.
LED4 cathode terminal.
LED5 cathode terminal.
LED6 cathode terminal.
Analog Dimming Control (Active high).
Pulse width modulation ‘PWM’ (Active high).
Connect a capacitor for filtering the PWM signal.
Charge pump output connected to the LED anodes.
Charge pump input, connect to battery or supply.
Connect to GND on the PCB.
PIN FUNCTION
VIN is the supply pin for the charge pump. A small 1 m F
ceramic bypass capacitor is required between the VIN pin
and ground near the device. The operating input voltage
range is from 2.4 V to 5.5 V. Whenever the input supply falls
below the under ? voltage threshold (1.8 V), all the LED
channels are disabled and the device enters shutdown mode.
ADIM is the one wire dimming input for all LED channels.
Levels of logic high and logic low are set at 1.3 V and 0.4 V
respectively. When ADIM first transitions from low to high,
each LED channel current is set to 25 mA. Each subsequent
pulse will decrement the current by about 3% from the full
scale.
PWM is the pulse width modulation input pin. When in
logic high condition, the LED current in all six channels
equals the programmed level set via ADIM. When PWM is
low, the LED current is set to 0 mA. This allows the average
LED current to be programmed by the PWM duty cycle. To
place the device into “zero current” shutdown mode, the
ADIM or PWM pin must be held low for 20 ms typical.
VOUT is the charge pump output that is connected to the
LED anodes. A small 1 m F ceramic bypass capacitor is
required between the VOUT pin and ground near the device.
GND is the ground reference for the charge pump. The pin
must be connected to the ground plane on the PCB.
C1+, C1 ? are connected to each side of the ceramic bucket
capacitor C 1 .
C2+, C2 ? are connected to each side of the ceramic bucket
capacitor C 2 .
LED1 to LED6 provide the internal regulated current
source for each of the LED cathodes. These pins enter
high ? impedance zero current state whenever the device is
placed in shutdown mode.
TAB is the exposed pad underneath the package. For best
thermal performance, the tab should be soldered to the PCB
and connected to the ground plane.
CPWM is the pin for connecting an external capacitor used
to filter the PWM signal inside the CAT3649.
http://onsemi.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| CAT4139AEVB | BOARD EVALUATION DPP CAT4139A |
| CAT4201AEVB | BOARD EVALUATION DPP CAT4201A |
| CAT4238AEVB | BOARD EVALUATION DPP CAT4238A |
| CAT4240AEVB | BOARD EVALUATION DPP CAT4240A |
| CB1A-R-WM-12V | RELAY AUTOMOTIVE SPST 40A 12V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT3649HV3-GT2 | 功能描述:LED照明驱动器 6 channel quad mode LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CAT3661HV3-GT2 | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CAT37 | 制造商:TI 制造商全称:Texas Instruments 功能描述:CMOS White LED Driver Boost Converter |
| CAT37_05 | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:CMOS White LED Driver Boost Converter |
| CAT37_08 | 制造商:TI 制造商全称:Texas Instruments 功能描述:CMOS White LED Driver Boost Converter |
发布紧急采购，3分钟左右您将得到回复。