- 您现在的位置：买卖IC网 > Datasheet目录318 > CAT4002ASD-GT3 (ON Semiconductor)LED DR 2 CH EZ DIM I/F SC-88 Datasheet资料下载
参数资料
| 型号： | CAT4002ASD-GT3 |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/11页 |
| 文件大小： | 0K |
| 描述： | LED DR 2 CH EZ DIM I/F SC-88 |
| 标准包装： | 3,000 |
| 恒定电流： | 是 |
| 拓扑： | 线性（LDO） |
| 输出数： | 2 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 电源电压： | 2.4 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-TSSOP，SC-88，SOT-363 |
| 供应商设备封装： | SC-70-6 |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
CAT4002A, CAT4004A
31 * n
LED current + 125
R SET
Basic Operation
The CAT400XA uses tightly matched current sinks to
accurately regulate LED current in each channel
proportional to the current sourced from the RSET pin.
There are 32 different settings for LED brightness that can
be programmed through the EN/DIM pin. Tight current
regulation for all channels is possible over a wide range of
input and LED voltages due to independent current sensing
circuitry on each channel.
Each LED channel needs a minimum of 50 mV headroom
to sink a constant regulated current of 20 mA. If the input
supply falls below 2.0 V typical, the under ? voltage lockout
circuit disables all LED channels and resets the circuit to
default values. Any unused LED channels should be left
open.
LED Current Selection
After power ? up, the LED current is set by the external
resistor (R SET ) value and the number of pulses (n) on the
EN/DIM input as follows:
0.6 V
31
The full scale current is calculated from the above formula
with n equal to zero.
The EN/DIM pin has two primary functions. One function
enables and disables the device. The other function is LED
current dimming with 32 different levels by pulsing the input
signal, as shown on Figure 16. On each consecutive pulse
rising edge, the LED current is decreased by about 3.2%
(1/31 th of the full scale value). After 30 pulses, the LED
current is 3.2% of the full scale current. On the 31 st pulse, the
current drops to zero, and then goes back to full scale on the
following pulse.
Each pulse width should be between 200 ns and 100 m s.
Pulses faster than the minimum T LO may be ignored and
filtered by the device. Pulses longer than the maximum T LO
may shutdown the device. By pulsing the EN/DIM signal at
high frequency, the LED current can quickly be set to zero.
The LED driver enters a “zero current” shutdown mode if
EN/DIM is held low for 3 ms typical.
The dimming level is set by the number of pulses on the
EN/DIM after the power ? up, as shown in Table 7.
T HI
EN/DIM
Table 7. DIMMING LEVELS
Full Scale (Current in %)
100
97
94
90
87
84
81
77
74
71
68
65
61
58
55
52
48
45
42
39
35
32
29
26
23
19
16
13
10
6
3
0
100
Dimming Pulses [n]
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
T LED
T LO
T PWRDWN
100%
97% 94%
100%
LED
Current
Shutdown
32 Levels
3%
0%
Shutdown
Figure 16. EN/DIM Digital Dimming Timing Diagram
http://onsemi.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| CAT4003BTD-GT3 | IC LED DVR 3CH TSOT23-6 |
| CAT4004AHU2-GT3B | IC LED DVR 4CH EZ DIM I/F 8DFN |
| CAT4004VP2-T3 | IC LED DRIVER LINEAR 8-TDFN |
| CAT4008W-T2 | IC LED DRIVER LINEAR 16-SOIC |
| CAT4101TV-T75 | IC LED DRVR HP CONST CURR D2PAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT4002ATD-GT3 | 功能描述:LED照明驱动器 LED DR 2 CH EZ DIM I/F RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CAT4002B | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Constant Current Programmable LED Driver with 32 Dimming Levels |
| CAT4002BSD-GT3 | 功能描述:LED照明驱动器 LED DR 2 CH EZ DIM I/F RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CAT4002BTD-GT3 | 功能描述:LED照明驱动器 LED DR 2 CH EZ DIM I/ RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CAT4003BSD-GT3 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Constant Current Programmable LED Driver with 32 Dimming Levels |
发布紧急采购，3分钟左右您将得到回复。