- 您现在的位置：买卖IC网 > Datasheet目录318 > CAT4134HV2-T2 (ON Semiconductor)IC LED DRVR BKLGHT FLASH 12-TDFN Datasheet资料下载
参数资料
| 型号： | CAT4134HV2-T2 |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/12页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR BKLGHT FLASH 12-TDFN |
| 标准包装： | 1 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 2 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 900kHz，1.2MHz |
| 电源电压： | 2.8 V ~ 4.2 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFDFN 裸露焊盘 |
| 供应商设备封装： | 12-TDFN（3x3） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 产品目录页面： | 805 (CN2011-ZH PDF) |
| 其它名称： | CAT4134HV2-T2DKR |
CAT4134
Table 4. PIN DESCRIPTION
Pin #
1
2
3
4
5
6
7
8
9
10, 11
12
Name
FLASH
EN
PGND
AGND
LED2
LED1
RFLASH
RSET
VIN
SW
OVP
Function
Logic input, set high to select the flash mode.
Enable control logic input (Active High).
Power ground reference.
Analog ground reference.
LED channel 2, connected to the LED cathode.*
LED channel 1, connected to the LED cathode.*
Resistor connection to set Flash mode LED current.
Resistor connection to set Movie mode LED current.
Power supply input.
Drain connection of low resistance power MOSFET.
Over Voltage Protection comparator input
*LED1 or LED2 pin should not be left floating.
Pin Function
VIN is the supply voltage input. The device is compatible
with supply voltages down to 2.8 V and up to 4.2 V. Internal
under-voltage lockout (UVLO) circuitry will automatically
prevent the device from operating whenever the supply falls
below 1.9 V. For operation up to maximum rated loads a
bypass ceramic capacitor of 10 m F is recommended between
the VIN and GND pins near the device.
EN is the enable logic input (active high). When the pin
voltage is taken below 0.4 V, the device enters shutdown
mode, drawing nearly zero current. At pin voltages greater
than 1.4 V, the device is fully enabled.
FLASH is the logic input (active high) used to control Flash
mode operation. When the pin voltage is taken above 1.4 V,
the device transitions from Movie mode to Flash mode.
When the pin voltage is taken back below 0.4 V, the device
returns back to Movie mode operation.
RSET, RFLASH pins allow to set the LED current
respectively in Movie and Flash mode. These pins, regulated
at 1.2 V, must be connected to a pull-down resistor tied to
ground. The LED current is a function of the resistor value.
GND is the ground reference for the driver. The pin must be
connected to the ground plane on the PCB.
SW pin is the drain terminal of the internal low resistance
power switch. The inductor and the Schottky diode anode
should be connected to the SW pin. Traces going to the SW
pin should be as short as possible with minimum loop area.
This pin contains over-voltage circuitry which becomes
active above 18 V. In the event of an “open-LED” fault
condition, the device will enter a low power mode and the
SW pin will be clamped to approximately 21 V.
LED1, LED2 provide the internal regulated current for each
of the LED cathodes. These pins enter a high impedance
zero current state whenever the device is placed in shutdown
mode. In applications with only one string of LEDs, the two
LED pins should be tied together. LED pins should not be
left floating.
OVP is the overvoltage protection input pin. When the pin
voltage exceeds the 1.2 V overvoltage threshold (V OVP ), the
driver stops switching. The output VOUT then drops down.
As soon as the OVP pin voltage falls under the V OVP
threshold, the part starts switching again.
TAB is the exposed pad underneath the package. For best
thermal performance, the tab should be soldered to the PCB
and connected to the ground plane.
http://onsemi.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| CAT4137TD-T3 | IC LED DRVR WHITE BCKLGHT TSOT-5 |
| CAT4139TD-GT3 | IC LED DRVR WHITE BCKLGT TSOT-5 |
| CAT4237TD-T3 | IC LED DRVR WHITE BCKLGHT TSOT-5 |
| CAT4238TD-GT3 | IC LED DRVR WHITE BCKLGHT TSOT-5 |
| CAT4240TD-GT3 | IC LED DRVR WHITE BCKLGHT TSOT-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT4137 | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:CMOS Boost Converter- White LED Driver |
| CAT4137AEVB | 功能描述:BOARD EVALUATION DPP CAT4137A RoHS:是 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:* 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| CAT4137TD | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:CMOS Boost Converter - White LED Driver |
| CAT4137TD-GT3 | 功能描述:LED照明驱动器 LED Driver,Boost 5 LED,series RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| CAT4137TD-T3 | 功能描述:LED照明驱动器 Boost Converter White LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。