- 您现在的位置：买卖IC网 > Datasheet目录318 > CAT4240TD-GT3 (ON Semiconductor)IC LED DRVR WHITE BCKLGHT TSOT-5 Datasheet资料下载
参数资料
| 型号： | CAT4240TD-GT3 |
| 厂商： | ON Semiconductor |
| 文件页数： | 6/12页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHITE BCKLGHT TSOT-5 |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 800kHz ~ 1.3MHz |
| 电源电压： | 2.8 V ~ 5.5 V |
| 输出电压： | 38V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 产品目录页面： | 805 (CN2011-ZH PDF) |
| 其它名称： | CAT4240TD-GT3DKR |
CAT4240
Pin Description
VIN is the supply input for the internal logic. The device is
compatible with supply voltages down to 2.8 V and up to
5.5 V. It is recommended that a small bypass ceramic
capacitor (4.7 m F) be placed between the VIN and GND pins
near the device. If the supply voltage drops below 1.9 V, the
device stops switching.
SHDN is the shutdown logic input. When the pin is tied to
a voltage lower than 0.4 V, the device is in shutdown mode,
drawing nearly zero current. When the pin is connected to a
voltage higher than 1.5 V, the device is enabled.
GND is the ground reference pin. This pin should be
SW pin is connected to the drain of the internal CMOS
power switch of the boost converter. The inductor and the
Schottky diode anode should be connected to the SW pin.
Traces going to the SW pin should be as short as possible
with minimum loop area. An over-voltage detection circuit
is connected to the SW pin. When the voltage reaches 40 V,
the device enters a low power operating mode preventing the
SW voltage from exceeding the maximum rating.
FB feedback pin is regulated at 0.3 V. A resistor connected
between the FB pin and ground sets the LED current
according to the formula:
connected directly to the ground plane on the PCB.
I LED +
0.3 V
R1
The lower LED cathode is connected to the FB pin.
Table 4. PIN DESCRIPTIONS
Pin #
1
2
3
4
5
Name
SW
GND
FB
SHDN
VIN
Function
Switch pin. This is the drain of the internal power switch.
Ground pin. Connect the pin to the ground plane.
Feedback pin. Connect to the last LED cathode.
Shutdown pin (Logic Low). Set high to enable the driver.
Power Supply input.
Simplified Block Diagram
V IN
C1
SW
V OUT
C2
Ref
300 mV
1 MHz
Oscillator
Over Voltage
Protection
V IN
SHDN
Thermal
Shutdown
& UVLO
–
+
+
–
PWM
&
Logic
Driver
R S
LED
Current
GND
Current
Sense
FB
R1
Figure 17. Simplified Block Diagram
http://onsemi.com
6
相关PDF资料 |
PDF描述 |
|---|---|
| CAT93C56XI | IC EEPROM 2KBIT 2MHZ 8SOIC |
| CAT93C66XI | IC EEPROM 4KBIT 2MHZ 8SOIC |
| CAT93C86LI-G | IC EEPROM 16KBIT 3MHZ 8DIP |
| CAT9532WI-T1 | IC LED DRIVER LINEAR 24-SOIC |
| CAT9552HV6I-TG2 | IC LED DRIVER LINEAR 24-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT4240TD-GT3 | 制造商:ON Semiconductor 功能描述:IC LED DRIVER BOOST TSOT-23-5 制造商:ON Semiconductor 功能描述:IC, LED DRIVER, BOOST, TSOT-23-5 |
| CAT-42506 | 制造商:Thomas & Betts 功能描述:1/4' YELLOW 6 PCS. PER BAG |
| CAT4254VP2-GT3 | 制造商:Catalyst Semiconductor 功能描述: 制造商:ON Semiconductor 功能描述: |
| CAT431L | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:Low-Voltage Adjustable Precision Voltage Reference |
| CAT431LEUK-TE7 | 功能描述:基准电压& 基准电流 1.24V .5% RoHS:否 制造商:STMicroelectronics 产品:Voltage References 拓扑结构:Shunt References 参考类型:Programmable 输出电压:1.24 V to 18 V 初始准确度:0.25 % 平均温度系数（典型值）:100 PPM / C 串联 VREF - 输入电压（最大值）: 串联 VREF - 输入电压（最小值）: 分流电流（最大值）:60 mA 最大工作温度:+ 125 C 封装 / 箱体:SOT-23-3L 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。