参数资料
| 型号： | CAT5113ZI50 |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/13页 |
| 文件大小： | 0K |
| 描述： | IC POT DPP NV 100TAP U/D 8MSOP |
| 标准包装： | 96 |
| 系列： | DPP |
| 接片： | 100 |
| 电阻（欧姆）： | 50k |
| 电路数： | 1 |
| 温度系数： | 标准值 300 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 3 线串行（芯片选择，递增，增/减） |
| 电源电压： | 2.5 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
CAT5113
http://onsemi.com
3
Functional Diagram
Figure 1. General
Control
and
Memory
Power On
GND
Decoder
31
30
29
28
2
1
0
Transfer
Gates
Resistor
Array
5Bit
Nonvolatile
Memory
Store and
Recall
Control
Circuitry
5Bit
Up/Down
Counter
GND
Figure 2. Detailed
Figure 3. Electronic
Potentiometer
Implementation
VCC
CS
INC
U/D
RH
RW
RL
VCC
Recall
CS
INC
U/D
1 of 32
RH
RW
RL
RH
RW
RL
Pin Description
INC: Increment Control Input
The INC input moves the wiper in the up or down direction
determined by the condition of the U/D input.
U/D: Up/Down Control Input
The U/D input controls the direction of the wiper movement.
When in a high state and CS is low, any hightolow
transition on INC will cause the wiper to move one
increment toward the RH terminal. When in a low state and
CS is low, any high-to-low transition on INC will cause the
wiper to move one increment towards the RL terminal.
RH: High End Potentiometer Terminal
RH is the high end terminal of the potentiometer. It is not
required that this terminal be connected to a potential greater
than the RL terminal. Voltage applied to the RH terminal
cannot exceed the supply voltage, VCC or go below ground,
GND.
RW: Wiper Potentiometer Terminal
RW is the wiper terminal of the potentiometer. Its position on
the resistor array is controlled by the control inputs, INC,
U/D and CS. Voltage applied to the RW terminal cannot
exceed the supply voltage, VCC or go below ground, GND.
RL: Low End Potentiometer Terminal
RL is the low end terminal of the potentiometer. It is not
required that this terminal be connected to a potential less
than the RH terminal. Voltage applied to the RL terminal
cannot exceed the supply voltage, VCC or go below ground,
GND. RL and RH are electrically interchangeable.
CS: Chip Select
The chip select input is used to activate the control input of
the CAT5113 and is active low. When in a high state, activity
on the INC and U/D inputs will not affect or change the
position of the wiper.
Device Operation
The CAT5113 operates like a digitally controlled
potentiometer with RH and RL equivalent to the high and low
terminals and RW equivalent to the mechanical
potentiometer’s wiper. There are 100 available tap positions
including the resistor end points, RH and RL. There are 99
resistor elements connected in series between the RH and RL
terminals. The wiper terminal is connected to one of the 100
taps and controlled by three inputs, INC, U/D and CS. These
inputs control a sevenbit up/down counter whose output is
decoded to select the wiper position. The selected wiper
position can be stored in nonvolatile memory using the INC
and CS inputs.
With CS set LOW the CAT5113 is selected and will
respond to the U/D and INC inputs. HIGH to LOW
transitions on INC will increment or decrement the wiper
(depending on the state of the U/D input and seven-bit
counter). The wiper, when at either fixed terminal, acts like
its mechanical equivalent and does not move beyond the last
position. The value of the counter is stored in nonvolatile
memory whenever CS transitions HIGH while the INC input
is also HIGH. When the CAT5113 is powered-down, the last
stored wiper counter position is maintained in the
nonvolatile memory. When power is restored, the contents
of the memory are recalled and the counter is set to the value
stored.
With INC set low, the CAT5113 may be de-selected and
powered down without storing the current wiper position in
nonvolatile memory. This allows the system to always
power up to a preset value stored in nonvolatile memory.
相关PDF资料 |
PDF描述 |
|---|---|
| X9C104SZ | IC XDCP 100-TAP 100K EE 8-SOIC |
| MS3450L24-7SZ | CONN RCPT 16POS WALL MNT W/SCKT |
| CAT5113LI-00-G | IC POT DIGITL 100K 100TAP 8DIP |
| MS3450L24-7SY | CONN RCPT 16POS WALL MNT W/SCKT |
| CAT5113LI-50-G | IC POT DIGITL 50K 100TAP 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT5113ZI-50-G | 功能描述:数字电位计 IC DPP,NV 100 taps Up/Down RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| CAT5113ZI-50-GT3 | 功能描述:数字电位计 IC DPP,NV 100 taps Up/Down RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| CAT5113ZI-50-T3 | 功能描述:数字电位计 IC DPP,NV 100 taps Up/Down RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| CAT5113ZI-50TE13 | 制造商:ON Semiconductor 功能描述:Digital Potentiometer 100POS 50KOhm Single 8-Pin MSOP T/R |
| CAT5114AV4-00 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述: |
发布紧急采购，3分钟左右您将得到回复。