参数资料
型号: CAT6243-ADJCMT5T
厂商: ON Semiconductor
文件页数: 10/16页
文件大小: 0K
描述: IC REG LDO ADJ 1A 6WDFN
标准包装: 3,000
稳压器拓扑结构: 正,可调式
输出电压: 0.8 V ~ 5 V
输入电压: 1.8 V ~ 5.5 V
稳压器数量: 1
电流 - 输出: 1A
工作温度: -40°C ~ 85°C
安装类型: *
封装/外壳: *
供应商设备封装: *
包装: *
CAT6243
PIN FUNCTIONS
V IN
Positive Power Input. Power is supplied to the device
through the V IN pin. A bypass capacitor is required on this
pin if the device is more than six inches away from the main
input filter capacitor. In general it is advisable to include a
small bypass capacitor adjacent to the regulator. In
battery ? powered circuits this is particularly important
because the output impedance of a battery rises with
frequency, so a bypass capacitor in the range of 1 m F to 10 m F
is recommended.
GND
Ground. The negative voltage of the input power source.
The center pad on the back of the package is also electrically
ground. This pad is used for cooling the device by making
connection to the buried ground plane through solder filled
vias or by contact with a topside copper surface exposed to
free flowing air.
ENABLE
ENABLE is an active high logic input which controls the
regulator ’s the output state. If ENABLE < 0.4 V the
regulator is shutdown and V OUT = 0 V. If ENABLE > 1.6 V
the regulator is active and supplying power to the load.
If the regulator is intended to operate continuously and
won’t be shut down from time to time ENABLE should be
tied to V IN .
BYP
The Bypass Capacitor input is used to decrease output
voltage noise by placing a capacitor between BYP and
ground. The recommended range of capacitance is from
100 pF to 470 pF. Values larger than this will provide no
additional improvement and will further extend CAT6243’s
startup time.
A bypass capacitor is not required for operation and BYP
may be left open or floating if no capacitor is used but DO
NOT ground BYP as this will interfere with the error
amplifier ’s functioning.
ADJ
ADJ = Adjust and is the voltage control input. ADJ
connects to the center point of a resistor divider which
determines the CAT6243’s output voltage. See Applications
Section for resistor selection guidelines.
V OUT
V OUT is the regulator ’s output and supplies power to the
load. V OUT can be shut off via the ENABLE input. All
CAT6243 members are designed to block reverse current,
meaning anytime V OUT becomes greater than V IN the pass
FET will be shut off so there is no reverse current flow from
output to input. CAT6243 is also equipped with an output
discharge transistor that is turned ON anytime ENABLE is
at a logic Low. This transistor ensures V OUT discharges to
0 V when the regulator is shutdown. This is especially
important when powering digital circuitry because if V OUT
fails to reach 0 V their POR (power ? ON reset) circuitry may
not trigger and scrambled data or unpredictable operations
may result.
A minimum output capacitor of 2.2 m F should be placed
between V OUT and GND to insure stable operation.
Increasing the size of C OUT , up to 22 m F, will improve
transient response to large changes in load current.
http://onsemi.com
10
相关PDF资料
PDF描述
CAT6500HVA-T2 IC POWER SELECTOR SW 3A 32-WQFN
CAT660EVA-GT3 IC REG SWITCHED CAP DBL INV 8SOI
CAT661EVA-GT3 IC REG SWITCHED CAP DBL INV 8SOI
CAT661EVA-T3 IC REG MULTI CONFIG 0.1A 8SOIC
CAT705ZI-GT3 IC SUPERVISOR CIRCUIT 8-MSOP
相关代理商/技术参数
参数描述
CAT6243-ADJMT5T3 功能描述:低压差稳压器 - LDO 1A ADJ LDO VOLTAGE REG RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
CAT6243DCADJ.RKG 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1 Amp Adjustable CMOS LDO Voltage Regulator
CAT6243DCADJ-RKG 制造商:ON Semiconductor 功能描述:1A ADJ LDO VOLTAGE REG - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / 1A ADJ LDO VOLTAGE REG
CAT6243DTADJ.RKG 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1 Amp Adjustable CMOS LDO Voltage Regulator
CAT62C580 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller