- 您现在的位置：买卖IC网 > PDF目录169496 > CAT660CSA-TE13 (ON SEMICONDUCTOR) SWITCHED CAPACITOR CONVERTER, PDSO8 PDF资料下载
参数资料
| 型号： | CAT660CSA-TE13 |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHED CAPACITOR CONVERTER, PDSO8 |
| 封装： | 0.150 INCH, SOIC-8 |
| 文件页数： | 14/16页 |
| 文件大小： | 157K |
| 代理商： | CAT660CSA-TE13 |
CAT660
7
Doc. No. 5000, Rev. S
Figure 4. CAT660 Block Diagram
+
C2
V+
(8)
2
OSC
BOOST/FC
8x
(1)
OSC
(7)
LV
(6)
CLOSED WHEN
V+ > 3.0V
GND
(3)
CAP-
(4)
C1
+
CAP+
(2)
SW2
SW1
Ο
VOUT
(5)
(N) = Pin Number
OSCILLATOR FREQUENCY CONTROL
The switching frequency can be raised, lowered or driven from an external source. Figure 5 shows a functional diagram
of the oscillator circuit.
The CAT660 oscillator has four control modes:
BOOST/FC Pin Connection
OSC Pin Connection
Nominal Oscillator Frequency
Open
10kHz
BOOST/FC= V+
Open
80kHz
Open or BOOST/FC= V+
External Capacitor
—
Open
External Clock
Frequency of external clock
If BOOST/FC and OSC are left floating (Open), the
nominal oscillator frequency is 10kHz. The pump
frequency is one-half the oscillator frequency.
By connecting the BOOST/FC pin to V+, the charge and
discharge currents are increased, and the frequency is
increased by approximately 8 times. Increasing the
frequency will decrease the output impedance and ripple
currents. This can be an advantage at high load currents.
Increasing the frequency raises quiescent current but
allows smaller capacitance values for C1 and C2.
If pin 7, OSC, is loaded with an external capacitor the
frequency is lowered. By using the BOOST/FC pin and
an external capacitor at OSC, the operating frequency
can be set.
Note that the frequency appearing at CAP+ or CAP- is
one-half that of the oscillator.
Driving the CAT660 from an external frequency source
can be easily achieved by driving Pin 7 and leaving the
BOOST pin open, as shown in Figure 6. The output
current from Pin 7 is small, typically 1
A to 8A, so a
CMOS can drive the OSC pin. For 5V applications, a TTL
logic gate can be used if an external 100k
pull-up
resistor is used as shown in figure 6.
相关PDF资料 |
PDF描述 |
|---|---|
| CAT803TTBI-T10 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT810LSDI-GT3 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT810TTBI-T3 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT803LTBI-GT3 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT803MSDI-T10 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT660ELA | 功能描述:电荷泵 Ind Temp 100mA Out RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
| CAT660EPA | 功能描述:电荷泵 Ind Temp 100mA Out RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
| CAT660ERD8 | 功能描述:电荷泵 Ind Temp 100mA Out RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
| CAT660ESA | 功能描述:电荷泵 Ind Temp 100mA Out RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
| CAT660ESA-TE13 | 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:100mA CMOS Charge Pump Inverter/Doubler |
发布紧急采购，3分钟左右您将得到回复。